|01-29-2012 12:46 AM|
Tips from the beas
It is just condensation build up. And yes...Gigiddy!
|01-27-2012 11:43 AM|
|CJ7GoldenEagle||Hmm, okay. That all makes sense. Thanks, I'll pass that along.|
|12-27-2011 02:47 PM|
|sevenservices||and someone mentioned the PCV valve. That is where the steam would go when the water gets burned out of the oil. (vents the crankcase) If that is clogged, the steam may be rising into the dipstick channel.|
|12-27-2011 02:43 PM|
|sevenservices||she'll want to change oil every couple thousand miles if its all short trips. And yeah, run it to burn the water out. This is really common on the old cast iron harley engines as well. They need to be run for at least 30 minutes to clear the condinsation out of the oil.|
|12-27-2011 02:33 PM|
With a situation where no water is getting into the engine from leaking dipstick or oil filler cap. Driving through deep water is not needed to get water in the engine if the dipstick or oil filler cap has a poor seal. Just driving in a rain storm will put excessive water in the crankcase. Given these seals are good then the rust is caused by condensation. When you see condensation on the outside, there is a similar amount of condensation inside the engine. The engine oil has to get at or above the boiling point of the water to get rid of it.
Rust on the dipstick and or, condensation (white junk) on the oil filler cap, is a good indicator of this condensation not being eliminated properly.
There are two possible causes:
1) Short runs on a regular schedule, (less than 10 min at operating temperature) not driving long enough to fully warm up the engine.
2) (most likely) Thermostat is not keeping the coolant hot enough. Minimum coolant temp is 175 degrees F. If the temperature is not kept high enough the condensation will continue to collect causing these problems. A 185 degree F thermostat is minimum. Generally the dash gauge is not dependable to indicate the coolant is hot enough. At 175 F coolant, the engine oil will be about 200 F to 220 F. This hot oil is what is needed to cook out that moisture.
|12-27-2011 01:49 PM|
|Timberwolf||whenever you check the oil, just wipe a little of the oil along the top of the stick before you put it back|
|12-27-2011 01:28 PM|
|Garyk||When was the last time the PCV was changed?...|
|12-27-2011 11:22 AM|
|CJ7GoldenEagle||Okay, I'm just going to go with the assumption that it's condensation. Thanks for all the help and advice everyone.|
|12-25-2011 11:26 PM|
|yellowlabs||i have noticed mine looks the same way especially since it got cold here in NC. I dont drive it every day. I did have coolant leaking a while back due to warped head. replaced that. no coolant leaking down and not running hot. changed the oil twice since the head was replaced. put some cheap oil in one time to top it off from autozone.|
|12-25-2011 05:16 PM|
The oil looks a lil dirty but i don't see any signs of water in it.....so who knows.
|12-25-2011 04:00 PM|
|AntiTrust||yup, what they said, oil looks just fine i wouldnt worry about it to much|
|12-25-2011 03:49 PM|
|12-25-2011 03:47 PM|
Looks like mine, I barely drive it and when I do it is not far enough to burn enough of the moisture out of the engine.
Lots of start and stop driving might get the engine up to temp. but it doesn't get all the moisture burned off and can actually create more depending on the humidity.
|12-25-2011 03:06 PM|
|12-25-2011 02:38 PM|
|darkproximity||Looks like condensation maybe she let the Jeep sit a little too long? Top of the dipstick probably doesnt always get warm enough to burn off the water|
|12-25-2011 02:23 PM|
|07XMan2Door||I hate it when I get rust on my dipstick!|
|12-25-2011 01:48 PM|
|CJ7GoldenEagle||Okay, so she says she hasn't noticed any overheating problems. I looked at the dipstick and it seems to be pushed in all the way and the tube looks like it's in the block correctly. She was still driving it regularly around town in stop and go traffic when she noticed it was rusty again. It's been like 4 or 5 months since the last oil change, so maybe it's a little over-due. Here's a pic of the rusty dipstick. The rust is on the upper end of it. So maybe it is just condensation.|
|12-25-2011 02:07 AM|
|12-25-2011 12:49 AM|
|12-25-2011 12:16 AM|
|Nubby55||as i was reading thats what i was thinking, not getting it hot for a long time can cause condensation in the engine.|
|12-24-2011 11:46 PM|
|12-24-2011 11:41 PM|
|MickeYJ||About the topic......Gigiddy lol|
|12-24-2011 11:39 PM|
|CJ7GoldenEagle||No, she hasn't been doing any off-roading with it, so there's no way it could have sucked up water that way. I don't know of any over heating, but I'll ask her about it. I'll check to see if it seems to be sealing correctly tomorrow.|
|12-24-2011 08:46 PM|
|SiLlY||Yeah.. Foamy light brown is not good. Any overheating issues? Rough running? If there's water in there and she hasn't been in any pools of standing water, we can help you narrow it down. Like Dark said.. if the tube isn't sealing.. rain water could be seeping in. Let's hope that's the case. And this is assuming she keeps up with her scheduled oil changes? Otherwise.. after a long time.. condensation can be a factor, as well.|
|12-24-2011 08:15 PM|
sucking water up in the engine would (in enough quantity) hydrolock the engine and possibly damage it, which doesn't sound like the case..
check to make sure the dipstick tube is pressed into the block tightly, that the nut on the stud hasn't come loose and that the dipstick is sealing around the tube..
|12-24-2011 08:03 PM|
|JJraddles||There may be water in the engine or in the gas tank. Has it been off road where it could have sucked up any water?|
|12-24-2011 07:14 PM|
My sister has a '95 YJ. She's had it about a year now. When she first got it I was changing the oil for her and I noticed the dipstick was rusty. I told her about it and we got a new one for it--new dipstick and new dipstick tube. Today she told me the new one is rusty now. Does anyone have an idea what might be causing this?