Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Dual Battery Wiring/Alternator Questions

Join Wrangler Forum Today

Thread: Dual Battery Wiring/Alternator Questions Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-27-2011 09:10 PM

Yes, you need a longer belt, same ribs. The pulley on the alternator is smaller than on the compressor so it isn't that belt. Don't remember exactly. May be able to get the number off the belt.

here are some pics of the installation. Not pretty as I was working with some very limited tools. When I rebuild it now I will dress it up. All it is is two lengths of angle iron with the holes drilled to accomodate it and relieved across the middle. Put a strap across the top to protect from hitting the fins.

Hope this helps a little.
12-27-2011 05:11 PM
Originally Posted by ballistx View Post
I don't have A/C so I utilized that location to mount a 2nd alternator.
Do you need a different size belt in order to run a second alternator there?
12-27-2011 04:10 PM
dual batteries and dual alternators

I don't have A/C so I utilized that location to mount a 2nd alternator. Used a Motorcraft with external regulator so I could get 120VDC. I don't remember just what I used for a mount. Will try to get a picture of it this evening when I get home.

I got two smaller batteries and installed in the location of the normal battery. One for the standard system and one for the winch. If you want to run the other lights you can install a separate fuse block and use it to wire whatever you want. You can run a continuous duty solenoid to the new fuse block and power it from the switch power.

I installed a solenoid between the batteries and powered it from a momentary switch under the dash. Then, if the main battery was dead, or weak, I can just flip the momentary switch and that parallels the batteries.

I have temporarily abandoned the system as I was not close to the Jeep. Will now re-establish it over the next few months.

The 2nd battery can also be used for an emergency welder if need be.

I like the idea of 2 separate systems. I had the issue of having the winch solenoids weld during a vicious snowstorm (60mph winds and snowing) and left me stranded in the middle of the blizzard with no power. No one could get close enough to jumper as we were trying to rescue stranded people so we were pretty well inaccessible. Proved the point that when it can't happen, it will.
12-27-2011 03:52 PM
Timberwolf looks like a good option
12-27-2011 03:51 PM
sevenservices seems like it would work... never used one though.
12-27-2011 03:43 PM
econjo Could I use something like this to keep both batteries charged properly?

BSR Dual Battery Isolator Setup | Dual Battery Wiring Installation Setup
12-27-2011 02:24 PM
sevenservices if interested you can get an A/B switch from a marine (boat) shop to switch back and forth. some of the newer ones can be wired up for bat. 1, bat 2 or both.

12-27-2011 02:12 PM
Timberwolf mean greesns are probably overkill
you can swap in a higher amp alt from a gr cherokee
you want to upgrade all the wiring for it as well ( battery cables, grnds etc)

you can wire them basically 2 ways:

2 standard batt in parallel which will give more amps all the time. these should be identical batts of the same age
or wire a second marine type separately thru a switch or isolator which you attach the lights and winch to. it can also a serve as a backup for starting if the primary goes dead

there are a lot of write ups floating around for the specifics and diagrams
12-27-2011 02:01 PM
Dual Battery Wiring/Alternator Questions

So I just got a winch and some lights that I am going to put on my 1995 2.5 YJ. I have heard some talk about needing an extra battery to run the extra power for the lights and winch. I have 8 lights that will go on there. Eventually I plan on running onboard air and a sound system as well.

So my questions are:
1. Do I need a heavier alternator for two batteries? ( i.e. mean green or something along those lines)
2. How would I wire in the second battery?

Any help would be much appreciated. I'm usually pretty good with wiring but in this case I want to make sure everthing is right so I dont fry anything.

Thank you!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 06:38 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC