|01-27-2008 07:21 PM|
|01-27-2008 12:53 PM|
|Triple88a||Active, yeah he would have if he had some but you can still install them on top of the winch plate.|
|01-27-2008 09:17 AM|
|activelydying||Did you have to remove your tow hooks?|
|01-26-2008 08:44 PM|
|01-26-2008 08:41 PM|
|Triple88a||Kg i had in mind that little bracket on the side of the bumper that in your picture appears to be in the middle of the tire.|
|01-26-2008 08:40 PM|
i really found no place for that under my hood. on the the only place that would be big enough on the drivers side fender i installed the ARB compressor.
i also installed an additional warn interrupt relay for the winch. if a relay in that box burns itīs possible that the winch gets some power all the time. in that case in can become damaged if you donīt interrupt the power.
i spent all my money in my jeep and i donīt want some major damage because of some missing 50$ sagety parts.
the box is opened at the down side. but that doesnīt matter. my winch worked with the winch and the box completely under water. after that i cleaned the inside of the box with the garden hose. and now 6 months later it stiil works.
|01-26-2008 08:32 PM|
|01-26-2008 08:25 PM|
and i often heard about burned relays after heavy winch use in theses boxes. because of that i think i let it stay there on top of the winch. iīm there faster than under the hood with my fire extinguisher.
|01-26-2008 07:52 PM|
|kg4kpg||That's the Control Box. The power and ground cables, the cables to the electric motor and the remote cable go into it. It can go where you see it or wherever you want to put it. I think I'm going to put it under the hood, I don't like it here.|
|01-26-2008 07:51 PM|
|tobycat1||The control box, or the clutch control?|
|01-26-2008 07:16 PM|
|Triple88a||Kg whats that thing on the left of the winch for? looks good.|
|01-26-2008 06:09 PM|
Okay, I'll check it out. Here's the winch mounted on the factory bumper:
|01-26-2008 05:51 PM|
a steel cable is bad for am aluminum fairlead.
warn and milemarker make the same fairleads out of steel. it works perfect for me.
i think the warn steel fairlead that i have has the # W7608.
|01-26-2008 05:31 PM|
|kg4kpg||Looks good Nic. Up and down clearance isn't an issue for me, it's the roller itself. The plate mounts behind the bumper so the bottom of the fairlead hits the tube before I can tighten it down properly. I was under the impression a steel cable was bad for a Hawes fairlead so I hadn't considered it yet. I was just going to order synthetic rope and sell this new cable and roller fairlead. As usual, Just Empty Every Pocket.|
|01-26-2008 10:47 AM|
i made some solid metal bracket to fix the problem.
you could also install a steel fairlead instead of the rollet thing.
here are some pis how i did it:
|01-26-2008 09:55 AM|
|01-26-2008 09:26 AM|
I have the solution to your problem.
Send the stuff to me, and I will go ahead and mount it up for you. Just until you can spring some synthetic line and new hawse lead thing, of course.
|01-26-2008 08:36 AM|
|01-26-2008 08:27 AM|
|Vector6||you think its cold in SC ?|
|01-26-2008 08:11 AM|
Winch install blues
Well, between working long hours, console building, and teenager abusing (my daughter) I was able to get out in the cold and mount my winch. THE G%& DA#* ROLLER FAIRLEAD WONT BOLT TO THE MOUNT BECAUSE OF THE BOTTOM TUBE OF THE BUMPER! The winch barely fits. With the existing holes, is it safe to drill a second set of holes to move the winch backward about an inch? There is plenty of mount plate behind it. I went ahead and mounted it with the factory bumper until I can come up with a plan. IF I buy a synthetic winch line and hawes fairlead my problems would be solved, just can't drop another hundred bucks (or more) yet. Oh the agony! I'll add some pics to the thread later when the sun comes up.