|02-22-2012 11:49 AM|
|richh789||Put 1.5 spacers on. Looks OK. When they are shot, I'll get 33s. Could fit 35s but rubbing is why it was lifted in the first place. I put pics in profile|
|02-22-2012 07:44 AM|
|02-22-2012 07:41 AM|
|02-21-2012 06:35 PM|
|02-21-2012 06:27 PM|
|cpisani89||im sitting on 35"s with a 1.5" re leaf soa and .5" life shackles..i think it looks perfect.|
|01-05-2012 06:30 PM|
|richh789||I think the 30s look good with that 4 inch lift n soa. Looks like you could go to full flex and not rub anything. Nothing wrong with that|
|01-04-2012 01:18 AM|
That jack is 46" tall. Btw, I'm planning on getting some 37s.
|01-03-2012 10:32 PM|
SOA w custom Deaver springs that are nearly flat (0" lift) GenRight fenders & 35's, but I'm planning on 37's.
31's on a SOA set up will look like a scared cat!
|01-03-2012 10:32 AM|
|01-03-2012 10:29 AM|
|whY402Jay||It would look too crazy on my Jeep, unless it was built for off-road racing.|
|01-03-2012 10:28 AM|
|01-03-2012 10:21 AM|
|Ibuildembig||I had 6's on blackie about 9 years ago|
|01-03-2012 10:18 AM|
|banks316||3.5 BDS springs plus SOA would give you 9in lift, damn thats alot for a jeep|
|01-03-2012 09:18 AM|
|whY402Jay||Are you going to run stock leafs? I was thinking about doing SOA but I have 3.5" BDS leafs and would need bigger tires.|
|01-02-2012 05:32 PM|
|richh789||Yes, 31S. Right now they rub the the flares pulling out of the driveway. I jacked the frame up 6 Inches to see how it looks, looked fine. Most people seem to run 33s.|
|01-02-2012 02:08 PM|
|banks316||It's possible, a friend of mine wanted 31 or 32's but had almost no money lucky for him I have welders and, spare parts and steel. We did a soa lift on his 2.5l|
|01-02-2012 01:13 PM|
|whY402Jay||SOA with 31s?|
|01-02-2012 10:11 AM|
|billytheyj||Oops ignore that craptastic picture number two... unless you can read it. The first one shows "about" the correct angle for your pinion to have for sye and cv shaft.|
|01-02-2012 10:07 AM|
|01-02-2012 09:00 AM|
Thanks a million. Should rear yoke be in a straight line with driveshaft? Instructions from RC say don't change pinion angle. For the front I understand, don't want to change castor angles. I would think the rear should be pretty straight would eliminate any vibration, maybe ever so slightly down for when rear suspension is compressed.
I'm new to jeeps. Thanks for the help. is anyone can think of something else I should get before I start please let me know
|01-02-2012 02:15 AM|
|banks316||If you do a normal SOA drop pitman is fine. If you use lift springs with a soa use stock drop pitman and pick up a cross over setup like the Teraflex kit. Don't by shocks till the end, everyone's setup comes out diffetent. One your rdy for shock you need to flex both front and rear then measure the extened, and collasped length to get the right size for.your setup. After that if your on a budget you can order the size you need. Superlift mares some softride shocks that are only $45 each from 4wheelparts.|
|01-01-2012 06:44 PM|
Bout to do soa lift on my yj. Ordering rc perches n a drop pitman arm. I've heard you need high steer conv, I've heard you don't. I drive my jeep on road regularly. And don't want to lose driveability.
I have 31s right now, and completely stock. Should I order a track bar? I've read ibuildembigs wright up, fantastic by the way. Gonna relocate brake lines like in the right up. Any recommendations on shocks that work from another vehicle? This forum is great and thanks in advance