Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > New used tank install - fuel pump wont fit??

Join Wrangler Forum Today


Thread: New used tank install - fuel pump wont fit?? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-15-2012 11:42 PM
Brianmlove What year tj did the new tank come off of?
01-15-2012 06:03 PM
Black Magic Brakes
Quote:
Originally Posted by davekippen View Post
Good advice black magic! I unstrapped it from the skid plate (broke the straps in the process...) I put it up on a couple of bar stools in the garage with the middle "sagging". I turned on the salamander to get some heat on the tank, thinking it would help it become a little more pliable. It was reeeeeeaaaal close to fitting so I took some sand paper and worked the inside lip of the tank down just a hair. Not enough to screw up the seal (i hope). The combination of those things worked, I got that bastard in and locked down!

Now I just have to buy some new straps and bolt that b back in. Finally!
I have several sets of straps if you don't find them.
01-15-2012 02:06 PM
davekippen Good advice black magic! I unstrapped it from the skid plate (broke the straps in the process...) I put it up on a couple of bar stools in the garage with the middle "sagging". I turned on the salamander to get some heat on the tank, thinking it would help it become a little more pliable. It was reeeeeeaaaal close to fitting so I took some sand paper and worked the inside lip of the tank down just a hair. Not enough to screw up the seal (i hope). The combination of those things worked, I got that bastard in and locked down!

Now I just have to buy some new straps and bolt that b back in. Finally!
01-08-2012 08:10 PM
Black Magic Brakes
Quote:
Originally Posted by davekippen View Post
Even with it all the way compressed it still is too long. It will not compress far enough to where I can get the threaded ring to contact the tank threads.
It won't contact the tank threads because you have the tank sitting on the dimple on the bottom of the tank. Remove the tank from the skid and set the ends on 2x4's to let the middle of the tank sag.

As far as any other dimensional differences, that's due to your replacement tank being stored without a pump in it out in the air and as it dried out, it shrunk a bit. The plastic swells and changes shape and size a lot when it's full of fuel.

It's a very common misconception that the spring loaded part of the fuel pump assembly is there to allow the bottom of the tank to be pushed up without moving the pump up against the lockring. What is overlooked is the fully compressed height of the fuel pump assembly is the height of the tank. There is no room for it to compress when it's installed.

Also, your replacement tank may have been stored with something sitting on top of it which has caused the top to sag a bit.

Just prop the ends up and the pump will go right in.
01-08-2012 07:28 PM
davekippen Even with it all the way compressed it still is too long. It will not compress far enough to where I can get the threaded ring to contact the tank threads.
01-07-2012 05:42 PM
Jerry Bransford Not quite clear on what is the difference but are you basing this on the fuel pump seemingly being too long to fit? If so, the fuel pump assembly is spring-loaded so you have to push down on it so the knurled ring can be screwed down into place.
01-07-2012 03:11 PM
TreeClimber1
Quote:
Originally Posted by davekippen View Post
, the 2 tanks are the same physical size, the only difference is how long the fill tube is on the inside.
I believe that is correct.
01-07-2012 02:10 PM
davekippen It was sold to me as the 19 gallon which is the larger one. I guess there is always a chance they said it was 19 but its really the 15. But from everything I have read, the 2 tanks are the same physical size, the only difference is how long the fill tube is on the inside.
01-07-2012 01:45 PM
Plowboy1970 There is two tank sizes. Wonder if the "new" one is the smaller tank.
01-07-2012 01:32 PM
davekippen
New used tank install - fuel pump wont fit??

My 99 TJ tank sprung a leak so I bought a used replacement. The hole on the new one measures about 1/4 inch narrower, and from the bottom of the tank to the top of the threaded ring is 1/2 inch shorter on the new one?? Is there really a difference or is it because maybe it sat around in a salvage yard and the tank dimensions changed? (I dont know how much that plastic would really change with the weather??) I cant get the fuel pump in the new one. Thoughts???

Tank on the right is the original one, the tank on the left is the new used one. By eye they look identical.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:45 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC