Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > full door adjustment

Join Wrangler Forum Today


Thread: full door adjustment Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-18-2012 08:14 PM
tailhole Well it didn't work out like i like. I did get it a little better.
I now need some touch up paint. When i broke the bolts loose it took the paint around them with it.
Im thinking its been repainted at some time.
The bottom hinge was stuck good to the door, and didnt want to move.
I will try again this weekend when the kids aren't bugging me.
01-18-2012 06:24 PM
Jeepzjlover Could you just use an air impact? Impacts take things out easier
01-18-2012 01:19 PM
tailhole That's what I was going to use. Just making sure y'all wasn't talking about a air impact
01-18-2012 01:16 PM
tailhole Hit it with a hammer
01-18-2012 01:16 PM
Jerry Bransford
Quote:
Originally Posted by tailhole View Post
Your talking about this right
Yes, that will work perfectly if it has a 3/8" drive. It almost looks like it has a 1/4" drive which would be too small to provide the force needed.
01-18-2012 01:16 PM
tailhole
Quote:
Originally Posted by Jerry Bransford
Yes, an impact screwdriver would be ideal for those particular bolts. Those are not the kind of bolts you want to take any chances on. Like the Craftsman at Craftsman Hand Impact Driver | Toolmonger which has a 3/8" drive output which fits that size torx-adapter.

That tool would be a wise thing to use to get those bolts out, they commonly cause problems.
Your talking about this right
01-18-2012 01:06 PM
Jerry Bransford Yes, an impact screwdriver would be ideal for those particular bolts. Those are not the kind of bolts you want to take any chances on. Like the Craftsman at Craftsman Hand Impact Driver | Toolmonger which has a 3/8" drive output which fits that size torx-adapter.

That tool would be a wise thing to use to get those bolts out, they commonly cause problems.
01-18-2012 12:39 PM
ballistx
farmer's impact wrench

When you attack the torx bolts, have a torx that allows you to strike the back side. Then as you are applying rotational pressure, tap (assertively) on the back of the wrench. That will give an impact like action to loosen it. You can do the same thing with a screwdriver or torx driver. Usually loosens them up.
01-18-2012 12:27 PM
Jerry Bransford One thing I forgot to say when I suggested to be careful when loosening those six hinge bolts.... those particular bolt heads are fairly soft and it's not hard to strip them out. It's a PITA to get them out once their torx-head opening has been stripped.
01-18-2012 12:23 PM
tailhole Door side. gotcha.
01-18-2012 11:53 AM
Jerry Bransford As recommended above, it is adjusted by loosening the hinge bolts on the DOOR-side of the hinge. Close and latch the door, loosen the six torx-head bolts in the door side of the hinge. Use a non-metallic part to move the door around a little until it is centered in the opening, then retighten the bolts.

Be careful when loosening those bolts. Be sure to use the right size Torx adapter and be ready for a fight as they are usually tight. Press the torx adapter into the torx bolts firmly and squarely to help prevent it from stripping out the bolt yead. Use a 1/2" ratchet drive with a 1/2" to 3/8" adapter to fit the torx adapter which is a 3/8" drive size. Don't quote me but it seems those door hinge bolts are perhaps a T-45 size... maybe T-40.
01-18-2012 11:40 AM
AtcoTrailsINC Not 100% sure here so hopefully someone will chime in...when i swapped my full doors for half doors i had to adjust mine by loosening the bolts on the door side ( DONT loosen the body side hinge bolts) this gave me enough adjustment to have my doors fit great. Also, make sure you use the rite size torx and a quality one at that, wouldnt wanna strip them out.
01-17-2012 09:01 PM
tailhole
full door adjustment

I don't use the pass side door much. But it is hard to open (kids having trouble) and it pinches the weather striping around the window and the hard top. I looked today after my youngest couldn't get it open and the striping has torn now.
I've loosen the bolts on the top and tried to push it back a little. but it didn't help.
I sure it doesn't make a difference but the top is a older one with the vents on a 05.

I guess what i wanting to ask is,
Is there any adjustment in the hinges? (if i can get the bolts loose)
Or just need to bend on it.
I just waiting for one of these kids to pull the handle out of the door.
Its looking like the top of the door needs to go towards the the front (maybe)

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:42 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC