Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > lower ball joint replacement

Join Wrangler Forum Today


Thread: lower ball joint replacement Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-04-2012 12:52 PM
SilverSport Raybestos makes adjustable BJs for the JKs. Available through NAPA and Rock Auto.
01-23-2012 11:39 AM
the Kolector Supposedly these are adjustable. Not sure of quality though.
FULLY ADJUSTABLE CAMBER CASTER ALIGNMENT OFFSET LOWER BALL JOINT KIT YJ TJ XJ JK | eBay
01-23-2012 11:22 AM
EAD Offroad
Quote:
Originally Posted by JIMBOX View Post
--YUP although mine are for the Rubi dana 44s and are -PPM-HD-BALL JOINT SYNERGY JK -N--
The knuckles on the front axles are the same on all JKs 07-12. The Synergy JK BJs fit D30 or D44 Rubicon. The upper BJ is also the same part number as the pre 2007 D30 or D44.

BJ-3134D = JK/TJ/LJ/YJ/XJ/ZJ single upper
BJ-3161A = JK - single lower
BJ-3171A = TJ/LJ/YJ/XJ/ZJ single lower

PPM-8009-12-01 = JK - 1 upper and 1 lower
PPM-4120-01 = TJ/LJ/YJ/XJ/ZJ - 1 upper and 1 lower
PPM-8009-12-02 - Replacement Boots - fit all of the above.
01-23-2012 10:40 AM
JIMBOX --YUP although mine are for the Rubi dana 44s and are -

PPM-HD-BALL JOINT SYNERGY JK -N--about $300 bucks a set and you just greasem when you change your oil-





JIMBO
01-23-2012 10:16 AM
EAD Offroad
Quote:
Originally Posted by AZduck View Post
JIMBO is right on when he says the need is RARE. Unless there are a lot of rough miles on that JKU, you should get a second opinion on your front end problems.
I think Jim may have been referring to the Synergy BJs lack of adjustment.

Synergy BJs are a zero degree offset BJ (just like stock), i.e. no adjustment. I'm guessing the OP's mechanic is suggesting some uppers with an offset to address a camber issue. As far as I know there are no JK ball joints with a non zero degree offset available.

TJ D30/D44 upper ball joints are actually the same as JK uppers but the lowers have a different taper. The lowers look the same eyeballing them but the taper is not correct on the knuckle. In theory you could mix and match TJ/JK uppers and lowers but I think that would be asking for trouble. If your camber is off there are other ways to address that.


Shot ball joints on an 07 is very common and BJs are relativity easy to swap with the right tools.

These are the videos Jim mentioned showing how to remove and re-install the Synergy BJs.
Jeep JK Ball Joint Installation - Part 1 of 2 Removal - YouTube
Jeep JK Ball Joint Installation - Part 2 of 2 Install - YouTube

The lowers are easy and the uppers are a bit harder (some people use the work b*tch ), take your time you should be fine.


I believe Synergy are out of stock of HD BJs until the end of the month. If you need some sooner EAD has them in-stock with free shipping. Synergy Suspension Jeep JK Heavy Duty Front Ball Joints Set
01-22-2012 09:49 AM
AZduck JIMBO is right on when he says the need is RARE. Unless there are a lot of rough miles on that JKU, you should get a second opinion on your front end problems.
01-22-2012 09:41 AM
JIMBOX google "Jeep JK/JKU Ball joint replace"--pages of info and

Don't replace JUST THE BOTTOM--do all four/have done if you haven't got the desire to doit

I recommend Synergy HD greaseable replacement Ball Joints for the JK/JKU-
google them for prices/avail and they aren't adjustable--the NEED for those is rare-price should be under $300 bucks and they are SUPER-

Good luck

JIMBO
01-22-2012 01:39 AM
DrHolliday
Quote:
Originally Posted by Vlj81
back story... i bought a jk 07 unlimited. put a lift on it and i went in wanting an alignment, lower ball joints are shot and i neet adj uppers they want to charge 1200 in all i can do most by myself ... this is somthing that i have not done. basics im looking for step by step and tools needed... to see if i can do this or just put in the hands of others...
Search you tube. There is a good video on there about changing the ball joints on the jk. They list the parts/ tools needed. And you more then likely will just need to buy the ball joint press from harbor freight.
01-22-2012 12:18 AM
Vlj81
lower ball joint replacement

back story... i bought a jk 07 unlimited. put a lift on it and i went in wanting an alignment, lower ball joints are shot and i neet adj uppers they want to charge 1200 in all i can do most by myself ... this is somthing that i have not done. basics im looking for step by step and tools needed... to see if i can do this or just put in the hands of others...

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:21 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC