|03-19-2012 10:06 AM|
|03-18-2012 09:57 PM|
|Calys003||Spod it's worth it. So easy to add anything. I don't have much yet but it gives me a reason to add lights & stuff|
|03-18-2012 09:29 PM|
|03-18-2012 06:13 PM|
|Mopar2Ya||I'm looking for a place to put switches (plasmaglow activator, needs ~1" of depth) on my '12. Is there a lot of room behind the oem net panel, where the daystar goes? Is there a lot of room behind the A-piller? Do A-piller switches when lit up cause any distraction while driving?|
|02-16-2012 12:18 PM|
There's three switches there now, added one when I added the Viair system.
|02-15-2012 11:59 PM|
sPOD on 12 JKUR
I waited back in Nov 2011 for two months for the panel. Got fed up and bought sPOD. $$ But now I'm glad I did. Very clean and all of my fuses and wiring are clean.
|02-13-2012 04:48 PM|
|02-13-2012 02:02 PM|
With regards to the Daystar panel - KJ71034BK, I can't seem to pull the old panel straight out like the instructions say. I have a 2012 Rubi-auto.
It almost looks as though I need to take the center console panel off because there is a lip on the cargo net panel at the bottom.
Anyone have any suggestions?
|02-12-2012 10:57 PM|
|NFRs2000NYC||I have mine on the left of the steering wheel, similar to jkjeeper06. Perfect location, right near the headlight switch, so all the lighting is in the same area.|
|02-12-2012 10:49 PM|
Heh Heh, yeah now that you mentionit-
|02-12-2012 10:33 PM|
|02-12-2012 09:33 PM|
Right over thr rearview mirror--
|02-12-2012 09:27 PM|
|02-12-2012 09:19 PM|
|jkjeeper06||What about here?|
|02-12-2012 08:40 PM|
|gr8fulKID||I have mine sticking out of the area right underneath the steering wheel column. Only downside is I cant see the little green light if it is one, but other than that its an easy spot to throw it.|
|02-06-2012 11:36 PM|
|Jsjk||Day star switch panel no argument low profile easy access, I love mine, has room for 4 switch, I bout boat switch which can double up.|
|02-04-2012 01:54 PM|
|ThePalmBeachYeti||Yeah, the A-pillar one looks like something of interest.|
|02-01-2012 11:49 AM|
|Nadurra||Plastic under steering wheel.|
|02-01-2012 08:29 AM|
|Dusthol||I saw an a-pillar switch panel. Mounts on a-pillar at dash level. Think quadratec sells it.|
|02-01-2012 05:58 AM|
That's so much more refined than the light panel I have. Then again, mine was only $15 and I wanted it to look simple.
|02-01-2012 04:21 AM|
The auto dose not have that problem but I love the way the Daystar panel looks. changing the boot like jmb6420 will fix it. That is what a lot of guys in my club have done.
|01-31-2012 07:38 PM|
|01-31-2012 07:29 PM|
|jmb6420||Installed one on my 08. The shift boot does contact it (switches 2&3 mainly). I solved the problem by changing my shifter boot. Got if from Redline|
|01-31-2012 05:41 PM|
|01-31-2012 05:33 PM|
I mounted mine here:
Wherever you decide to go just make sure there is room behind the panel you drill through.
Yeah I know, it needs a bath.
|01-31-2012 05:20 PM|
Where to put my KC switch for my new lights? Daystar switch panel?
I purchased a set of KC lights for my windshield, great quality light can't wait to have them up and running. But my actual concern is where to mount the switch with out doing a hack job, so I looked around and found this from daystar on qudratec's website.
Daystar KJ71034BK - Daystar Lower Dash Switch Panel for 11-12 Jeep® Wrangler & Wrangler Unlimited JK - Quadratec
Is anyone familiar with this product and it's fitment an matching quality also is it a direct fitment? another question is that I drive a 6 speed will it be a problem with the shifter?
If anyone has one installed please post a picture on here