|02-22-2013 09:15 AM|
|NolaTJ86||After doing a lot of research and reading I think I am going to get the zone 4.25" combo kit over the RE 2-2.5" budget boost. I have a 2000 TJ Sahara, 4.0L i6 auto, currently running 31"x10.5 pro comp all terrains. Will it make a huge difference if I continue to run the 31" tires until they wear out, they are almost brand new (complete noob question sorry). I will probably get the jks front adjustable track bar and the steering stabilizer. Would I have to regear after the install and/or after I went to 33" tires?. Once again noob question but does the disconnect option mean? What would that do if I got it?|
|02-13-2013 05:27 AM|
|TJSurf||Yes, you can install the 3" SL now and wait to add the BL/MML if you want. I've had the 3" lift for about 4 month and plan on adding the BL/MML soon.|
|02-06-2013 07:41 AM|
I am getting ready to pull the trigger and buy either the 3" suspension lift or the 4.25" combo kit both by Zone.
My question is if i buy the 4.25" can i install the 3" suspension lift now and wait to see if i want to add the BL and MML? If i like the look i may just sell these parts but it sure is cheaper to buy the 4.25 kit versus the 3" and later buy a BL and MML.
|07-17-2012 05:39 AM|
|07-17-2012 05:08 AM|
|jefferyc22||Bump.....how are these 4.25 combo lifts holding up?|
|02-17-2012 12:46 AM|
|02-16-2012 11:01 PM|
I haven't done anything to my brake lines. I got a front JKS tracbar. So far I haven't had to do the SYE and no vibes.
|02-16-2012 09:38 PM|
|cntryboy232||if i do the zone lift will i have to extend brakelines? what else needs to be done when kit is installed other than the sye and tracks?|
|02-14-2012 02:38 PM|
|02-14-2012 12:39 PM|
|Coasttrash||s3nt3ncd3, that extra bolt from the rear trac did you re-use your stock bolt on the rear trac bar bracket? That extra bolt is to replace the trox bolt. Atleast thats what I used it for.|
|02-14-2012 10:54 AM|
|Daydreamnation0312||Hey guys I'm really looking into getting the 4.25 Zone lift combo with some 33's and I was wondering if it is a good lift that can take a beating when on the trails|
|02-10-2012 11:36 PM|
|GoldenSahara00||Yeah man, I'm not sure if the bushing is worn or the bolt is just slightly wrong. I had shifting like you at one point. But torqued it back down hard and never had a problem again. it doesn't make sense that one hole works and another wouldn't, so it has to be some piece of hardware or something failing. Bushing bolt etc. I agree with you about the adj being nice but I'm gona plate the back of the braket with 1/4 in steel and drill tht as well I shouldn't have any issues then|
|02-10-2012 05:21 PM|
For the rear, I used the bracket Zone provided and installed it exactly as described...it's a pretty solid bracket. I think I did use one less bolt for it...for some reason I seem to remember it calling for bolt in various locations on it and we had one extra bolt it called for and no extra holes in the bracket to use it in. Regardless, it was very solid. For the front adjustable trackbar...don't drill the hole or install any brackets. Just use the original hole. If you want to reinforce it like UnlimitedLJ04 has mentioned in other threads, that's fine obviously, but I didn't do that using the stock hole.
|02-10-2012 03:41 PM|
|coors||Where did you get the lift for 499 shipped.|
|02-10-2012 02:30 PM|
|GoldenSahara00||The hole only wears out if you still it like they tell you. Get the right sized bolt and drill the corrected sized hole and it works fine. It still weakens the plate however so anything over 33s I would weld up some extra plate to back it. Thts what I'm doing when I'm workin on my next proj.|
|02-10-2012 08:22 AM|
Have you done this yet?
If so how did you do it?
Did you use the bar relocation brackets for the front and rear trackarms?
I am looking at getting adjustable front and rear trackarms to eliminate having to drill a hole that will very well wear out over time and cause a bigger problem. Now I also have read that rear trackbar might hit the gas tank or other things. I know your Jeep is a 2000 and mine is a 98 and I really think there is no or not much difference. Did you run into this? (again if you have already replaced the trackbars)
I appreciate all your help.
|02-10-2012 02:58 AM|
|s3nt3nc3d||My linkage was all messed up...it worked, but I had problems getting in and out of 4lo...I replaced the entire piece of junk setup with a Novak cable shifter. One of the best mods I ever did.|
|02-10-2012 01:03 AM|
|jeep-dj||i was thinking about the combo lift, did you have to adjust transfer case lever linkage?|
|02-10-2012 12:01 AM|
Heck man, I did my on body lift and I am no mechanic. It's the simpliest thing you can do. I did it all by myself with one jack. It took me a little over an hour to do the whole thing. Just spray down your bolts weeks in advance with some PB blaster and you will be fine.
I also recommend the mml. It;s not hard to do either and you want have to mess with lining the radiator back up. Grab wrench have fun
|02-09-2012 11:46 PM|
|shrekfx||O.k. I'll probably do the 3in to start then go from there.. I'll do the body later if i beside to go that route. Biggest issue is finding someone here to install a body without charging an arm and a leg and to find a place that will do one period.. Most places I checked here refuse to do body lifts. The place I'm going to get one installed is an authorized zone dealer just doesnt recommend doing it. Im sure I can convince them to, but I think he said it will cost a lot more to do it or something like that.|
|02-09-2012 11:40 PM|
Like it has been said above, I am running the 4.25 combo, not really all Zone because my body lift was all ready on before 3" suspension lift. I think you will be well pleased with the set-up.
|02-09-2012 11:31 PM|
I personally would do the combo over the 4 inch...but that's just me. If you do a lot more off-roading, the 4" will offer more suspension travel than the 3" obviously. IMO, for the average off-roader...the combo requires less work to "do it right" compared to the 4".
|02-09-2012 11:13 PM|
|GoldenSahara00||The arms on the zone lift are no where near as nice as a lot of others. And I don't think they are adjustable. So if you do get an sye you'll have to get all new arms. At least rear uppers to adjust pinion angle.|
|02-09-2012 11:10 PM|
From the looks of it, it does come with control arms.
But are you recommending the 3in over the 4in?
|02-09-2012 10:23 PM|
|02-09-2012 09:32 PM|
|shrekfx||Well after doing some reading and stuff I think I'm going to go with the 4" zone suspension kit. Seems to have everything I want/need with room to add some upgrade here and there. Thanks for the input, but it does seem like zone is the way to go on a budget. Plus its made by BDS just dont have the warranty. Just have to wait for march to get it installed.|
|02-09-2012 05:21 PM|
You'll be fine, you wont look "too" outta place
I'm currently running 32x11.5's on mine but will run 33x12.5's once these are shot...i also have flat fenders up front and flat flares in the rear (as of this weekend, anyway) so i've got a ton of room with the 32's and will still have a ton with the 33's
As for the step...i agree with the idea mentioned above, get some sliders with a built in step instead of getting the factory ugly bars that get hung up on rocks...i mean factory side steps
|02-09-2012 04:35 PM|
|shrekfx||O.k. well that rules out going to this guy. LOL.. For tire size, down the road i'll be going with 33s, but right now i'm using 31s.|
|02-09-2012 02:32 PM|
|02-09-2012 01:52 PM|
If you did like a short arm 6" lift...that would probably make it a bit more dangerous.
I can tell you based on real world experience, my Jeep is much more stable and comfortable now at 80mph on the interstate with the 4.25" combo, Cragar Soft 8 wheels, and 33x12.5 tires than it was stock with 31x10.5 tires. Stock, it was almost scary...
|This thread has more than 30 replies. Click here to review the whole thread.|