Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > won't start after replace 2.5 Engine

Join Wrangler Forum Today

Thread: won't start after replace 2.5 Engine Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-24-2012 07:58 AM
brentd711 Glad to hear it's running! Your cam should be fine, you did the critical part of the swap...putting your '88 flywheel on the '93 block.
02-23-2012 09:26 PM
SandyMushYJ Good call Brent!
02-23-2012 09:18 PM
azbill88yj It was the fuel lines were backwards at the TB. I swapped them before but it didn't make a difference. Now I realize I had the #1 plug wire in the wrong spot on the distributor cap. Thanks for pointing out my mistake... Now i'm running....

I am curious about the cam though. I'm going to check on that.

thank you!

02-22-2012 02:12 PM
Garyk You might want to check with someone familiar with engine swaps cause I don't think you can do what you did. the 93 was fuel injected and I would think would have a different cam in it along with the crank sensor etc. Just my thought on it...
02-22-2012 09:00 AM
brentd711 If the timing is off it shouldn't start even when you add fuel to the TB. Does it stay running after you prime it or just die as soon as you stop dumping in fuel? Any chance you have the supply and return lines reversed?
02-22-2012 08:32 AM
azbill88yj Currently it has the 88 distributor in it. I haven't checked how close it ls to TDC. But it runs if I pour fuel down the TB. Could timing cause it not to start unless I add extra fuel?
02-22-2012 07:42 AM
brentd711 Is the '88 distributor in the motor or the '93? Are you sure you're on TDC on the compression stroke? Can you get the distributor to align to #1 plug at TDC?
02-22-2012 12:53 AM
won't start after replace 2.5 Engine

I'm hoping for a little help with a frustrating problem...

I just replaced my 88 yj 2.5L engine with a 93 2.5L YJ engine but the engine won't start unless I pour gas or spray choke cleaner in the throttle body. The original motor ran fine but smoked extremely bad. I am using everything original from the 88 engine including the flywheel. I have double checked the crank position sensor and it is connected. I can see fuel hitting the throttle plate when I crank the motor and it fires the plugs fine. I checked the pressure from the fuel pump and it is slightly above 15 which should be ok. I dropped the tank to check the rubber hose and the fuel pump was rusted so I replaced it hoping to avoid problems down the road. New fuel filter as well. Blew out all the fuel lines with an air hose and they seem to be clear. I did notice that TDC on #1 doesn't match up with the #1 labeled position on the distributor cap, it's 90 degrees off. I have the 93 distributor and when I checked the rotor alignment to the distributor shaft bottom flat part it is 90 degrees off from the 88's. Anyone know if there is something that has to be done to get this motor to start.

sorry for the long winded explanation.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 10:23 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC