Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > dead yj please help ive done everything!!!!

Join Wrangler Forum Today


Thread: dead yj please help ive done everything!!!! Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-02-2012 06:28 PM
Rusty jeep I hope these help not very good pics
03-02-2012 05:07 AM
mikeaju That would be awsome thanks
03-01-2012 10:15 PM
Rusty jeep i will try 2 get a pic tomorrow
03-01-2012 08:11 PM
mikeaju i need a pic of a cam ensor inside a dist to know if i did it right or if it matters really it can only go one of two ways but it might matter idk
03-01-2012 06:25 PM
mikeaju and where on the flywheel do i need to have the knoch at i have it on the 2nd to last knoch on the right if your looking at the motor.
03-01-2012 06:24 PM
mikeaju im hoping i didnt put the cam sensor in wrong but it had a ratainer screw so it can only go one of teo ways is there any pics of that i havent found any of those.
03-01-2012 06:09 PM
Rusty jeep it was prob the cam sensor and the timing just got fuged ive done it my jeep sat in the back yard for almost a year i was so fed up with it
03-01-2012 06:06 PM
mikeaju ok ill try that its gotta be it idk what else it can be is so irritating.
03-01-2012 05:59 PM
Rusty jeep just a smig ahead
03-01-2012 05:57 PM
mikeaju ya i thought about that but i had spark so i wasnt worried i think i might still be off time like u said now should i be just ahaead or just behind or right on the number one post.
03-01-2012 05:54 PM
Rusty jeep did you check the roter ive seen them woller out
03-01-2012 05:50 PM
mikeaju it just stopped one morning i my driveway
03-01-2012 05:49 PM
Rusty jeep not that i can think of did you remove the dist or did it just stop running?
03-01-2012 05:46 PM
mikeaju ok i was holding it in the 11 oclock position and the rotor around the 5oclock position but i might be off it jus doesnt make sense that it wont fire at all. thanks for the advice could my problem be anything else?
03-01-2012 05:42 PM
Rusty jeep the haynes manuel, or google this is what i found.holding the centerline of the base slot in the 1 o'clock position Distributor Pre-position - All Engines Continue to engage the distributor into the engine. The rotor and distributor will rotate clockwise during installation. This is due to the helical cut gears on the distributor and camshaft. When the distributor is fully seated to the engine block, the centerline of the base slot should be aligned to the clamp bolt mounting hole on the engine Distributor Engaged Position - 4.0L 6-Cylinder Engine The rotor should also be pointed at the 5 o'clock position.
It may be necessary to rotate the rotor and distributor shaft (very slightly) to engage the distributor shaft with the slot in the oil pump gear. The same may have to be done to engage the distributor gear with the camshaft gear.
The distributor is correctly installed when:
  • the rotor is pointed at the 3 o'clock position (2.5L engine), or at the 5 o'clock position (4.0L engine)
  • the plastic alignment pin (or pin punch tool) is still installed to distributor.
  • the number 1 cylinder piston is set at top dead center (TDC) (compression stroke)
  • the centerline of the slot at the base of the distributor is aligned to the centerline of the distributor holddown bolt hole on the engine. In this position, the holddown bolt should easily pass through the slot and into the engine.
03-01-2012 05:33 PM
mikeaju really this sucks, is there any pics or videos that can help me dude im really dieing here my wife has a job lined up for next mon and we nned that jeep to start.
03-01-2012 05:31 PM
Rusty jeep nope mine was a tooth off did the exact same thing. had fuel, fire, no start
03-01-2012 05:29 PM
mikeaju so it wont even try to start if its a tooth off
03-01-2012 05:27 PM
Rusty jeep the timing marks need to be at top dead center on the compreshion stroke. i think the dist needs to be at 5 oclock
03-01-2012 05:24 PM
mikeaju i tried uploading pics of the rotor and stuff but it wouldnt, i put flywheel on 2nd tooth from bottom and rotor at about 4 oclock right on the number one.
03-01-2012 05:21 PM
busemans its cause you have a 4.0 liter v6. the jeep engine is an I6.


are your spark plug wires on properly? not opposite? maybe you are sparking but when the engine is on the second stroke that is clearing the exhaust out of the chamber?
03-01-2012 05:20 PM
Rusty jeep did you clock the distributor properley. sounds like it is a tooth off
03-01-2012 05:16 PM
mikeaju
dead yj please help ive done everything!!!!

92 yj renegade 4.0 ltr v6
changed cps, changed cam sensor, ignition coil, plugs, made sure its on time, i have fuel at the rail with alot of pressure and spark( kinda wierd though it will spark-spark then sparkspark like double it weird. anyway i have no start it wont even try and i have got a diff computer but it still wouldnt fire. Im at witts end im about to get rid of it cuz i need a second car please help anyone.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:19 AM.



Jeep, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC