|03-07-2012 08:45 PM|
|JDeBlois||Thanks. I'll be workin' on it tomorrow! I'll keep ya posted.|
|03-07-2012 08:36 PM|
|Jerry Bransford||Between the calipers and pads holding the rotors firmly and the fact that the rotors can be hard break free even with the caliper removed, rotor movement is not an issue.|
|03-07-2012 08:32 PM|
That toe alignment method that Jerry shows in the photo is really PERFECT...but I happen to know that....uh....I heard from a friend ......that it's easy to overlook that the brake rotors are bolted down to the hubs during this process.
If you don't do that, the rotors will rock a little, and the alignment won't be accurate.
|03-07-2012 08:21 PM|
|carl d||My Zone 3" Suspension Lift is working great. I agree get the alignment and I bet it will be fine.|
|03-07-2012 08:15 PM|
Basic Jeep Front End Alignment
That method involves measuring between the tires. That link also shows how to re-center the steering wheel once your toe-in is set. Both are extremely easy to do with nothing more than a wrench, pliers, and a tape measure.
A more repeatable/more accurate way of measuring between the tires is as shown below. Simply acquire two 1" square aluminum tubes and mark them at points equal to your tire diameter, then measure between them as shown.
One last comment... the tie-rod that you rotate to set the toe-in is often hard to turn the first time you try to adjust it since it can get stuck from dirt, corrosion, etc. If that happens, you can just a pipe wrench on it which will make the job easy. I carry a pipe wrench with me on the trail for when I have to adjust other people's tie rods for them after they've bent them.
|03-07-2012 08:08 PM|
|03-07-2012 08:07 PM|
|Jerry Bransford||A bad toe-in can encourage DW so see how it goes after you get your toe-in set. You've been here long enough to know you can easily and accurately set your own toe-in just as accurately as an alignment shop can right?|
|03-07-2012 08:02 PM|
I'm hopin' that fixes it?!
|03-07-2012 07:54 PM|
|03-07-2012 07:09 PM|
|03-07-2012 06:01 PM|
|Jp90Talon||Get an alignment then worry...trust me|
|03-07-2012 05:58 PM|
|03-07-2012 05:03 PM|
|03-07-2012 03:04 PM|
Is there *any* side-to-side movement you can detect where the new track bar is bolted to the axle as an assistant turns the steering wheel left/right with the tires on the ground? The track bar mounting bolts need to be tight enough that there can be zero (!) side-to-side movement at its mounts as the steering wheel is turned back & forth.
Did you also install bigger tires?
|03-07-2012 02:57 PM|
Four main things...
#1 Do the alignment
#2 Make sure all tires are balanced
#3 Make sure all bolts are truly tight
#4 Do the alignment!!!
To be honest an alignment is simple to do on your own if you take the time to learn on a jeep. Plus it will save you a ton down the road.
|03-07-2012 02:25 PM|
3 inches and Death Wobble?!
Hey y'all. I have some serious DW at about 30 mph (or anytime when I let off the gas) after installing my 1 in. mml and my 3 in. Zone Offroad suspension lift. I need a serious alignment and am having that get done Friday. Will the alignment and toe in alone solve my DW?
I have a 2 mnth old HD steering stabilizer so I know that's not the issue and I also installed a Rubi Express adjustable front track bar with my lift.
Any ideas on what I could do or if the alignment and toe in will solve it?