|05-16-2012 11:52 PM|
|OUTAGAS||Hi everyone! I just got my TF leveling/Grade 8 Bolt kit from NorthRidge4x4 this evening and will be installing them tomorrow. Can anyone give me some guidance/write up on how to properly do this project? I can only find some info on the leveling kit install but not on both. Thanks!|
|03-08-2012 11:32 PM|
Simple peace of mind.
|03-08-2012 11:29 PM|
Your stock one is fine for most wheeling applications. If you're gonna wheel your Jeep hard, you might want a beefier aftermarket version. And if you're worried about nailing it while wheeling, you can relocate so that it sits a little higher for fairly minimal cost.
I wouldn't remove it, though, as it does contribute to keeping your Jeep stable over rough surfaces.
|03-08-2012 11:22 PM|
Finally decided what the hell, just to be on the safe side...
You'll notice from my post that I really only cut the corner off. That's the dangerous part. And it really was an easy job.
There are some guys on JKF that say you shouldn't need to do it unless you're running 37's. But, like I said, there were several posts where guys with 35's had sliced a tire. So I caved.
|03-08-2012 11:00 PM|
Removing it for $0 sounds better than moving it for $50 or $100.
Ive heard many state "the stock one is fine", which has to be the only part on a jeep that is.
|03-08-2012 10:32 PM|
|ESP||Thanks wolf I hadn't seen that other thread. Looks easy enough and I can understand why you would want to do that. Is it still necessary if you don't disconnect the sway links, thoughts?|
|03-08-2012 10:26 PM|
When your suspension compresses, the rear tires move up and to the back. My worry was that, with swaybars discoed, and in the right circumstances (crawling over a log, crossing a deep rut on an angle) I was a little too close for comfort (I think I had like 1-3/4", iirc).
Basically, I cut mine simply out of a better-safe-than-sorry mindset. I must've read 20 threads on JKF...there were people whose seams were really close to their tires who didn't cut em, and some who had plenty of space but did cut em.
I also read several threads where guys thought they had plenty of room, then promptly went out and sliced one of their tires.
So I cut mine.
You've probably seen this, but here's how I did mine:
Cutting your pinch seam
|03-08-2012 10:16 PM|
The SS can even work against you by masking some of the early signs of DW.
|03-08-2012 10:14 PM|
|ESP||Regarding trimming the pinch seems, are there a few sets of 35s that you don't need to worry about this with? I guess it's hard to say given the availability and variance of wheel/tire packages.|
|03-08-2012 10:11 PM|
|03-08-2012 10:09 PM|
OK, sits too low.
|03-07-2012 02:50 PM|
|Thorshammer7||Installed my TF monday and have run about 200 mile on it. Rides/drives great see no need for the steering stabilizer.|
|03-07-2012 12:53 PM|
|03-07-2012 12:42 PM|
Basically the same thing for the rear, just didn't completely remove the sway bar end links. Removed the bracket holding the emergency brake cable to the tub. Used some lube on the rear puck and used the spring to press the puck into place. Bolted it all back up.
Very simple install and I have no doubt I could do it in less than an hour if I needed to. But no need to rush at this. Always take your time and make sure everything is done correctly.
|03-07-2012 08:32 AM|
|Mr. Sinister||I went with a 1 3/4 spacer lift, which is essentially the same thing, but retains the factory rake, which I like. Cake to install, and zero drawbacks. The rest of the suspension and steering is 100% stock, but I may replace the shocks at some point, which I wanted to do anyway.|
|03-07-2012 08:32 AM|
|03-07-2012 08:26 AM|
You don't need a new SS for your Jeep unless the stock one is broken.
And there's no need to trim your pinch seam unless you're running 35" tires (and then, maybe) or larger (and then, definitely).
The TF leveling kit works great, from what I've heard. Listen to these guys. ^^^^^
Here's a link to the polyperformance kit JK-Uknowit mentioned. Hard to believe, I know, but the bolts in your Jeep's stock TB's and LCA's are undersized, which can lead to serious problems down the road. Buy a set of the bolts in the link below and install them when you do your lift, and you'll be good to go.
The Importance of changing out stock bolts!!
|03-07-2012 08:22 AM|
|AC94||4fit, how did you install your kit without removing the tires? We are still talking about the TF pucks, yes?|
|03-07-2012 08:17 AM|
|4fit||The TF leveling kit is great for someone just looking for a little boost and a little added clearance for larger tires. I installed mine in 1.5 hours taking my time and without ever removing a tire from the Jeep. Well worth the ~$120.|
|03-07-2012 08:12 AM|
My TF leveling kit was a piece of cake. Install was easy and the instructions were easy to follow...if you use common sense. Just watch your brake lines. Be sure to remove brackets on the front and rear so you can get enough "droop" to get your springs out. I did nothing with the steering stabilizer.
Also, while you're under there, may as well upgrade to grade 8 hardware and trim your pinch seam. Kbwwolf will chime in here in a minute with all the links for that stuff. I'm not that savvy, I pretty much just do what he says!!
|03-07-2012 05:16 AM|
|03-07-2012 05:08 AM|
|OH9JK||Leveling kits are all the same. TF has great customer service should you run into an issue. The OEM steering stabilizer is fine when relocated.|
|03-07-2012 01:33 AM|
Input on leveling kit
Looking at the teraflex any pros and cons and should get the steering stabilizers too