Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > My 2012 JKU Horn Upgrade Install

Join Wrangler Forum Today


Thread: My 2012 JKU Horn Upgrade Install Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-09-2012 08:37 PM
tcass wow, they are singing in great harmony.

cass
03-09-2012 08:26 PM
JeeperJake thanks for a great tekkie post....some day I'll get around to doing an upgrade.
03-09-2012 10:32 AM
Matador Good stuff, thanks.
03-09-2012 10:01 AM
sclui56
Quote:
Originally Posted by Matador View Post
Is there a way to avoid cutting anything off, or splicing into the stock wiring? I thought these horns were a plug & play solution. I'm always weary of messing with any electrical connection of a vehicle with a can-bus system. Understandably, these are just horns and probably will have slim affect to anything if I messed with the wiring, but I would like to avoid it if I could.
I didn't want to splice into the wiring either, so I went to Radioshack and bought a bag of split connectors (mixed). I used the ones with one female end and 2 male terminals, the female end goes into the horn #1 termianl, and I plugged the factory wire into one of the male, then daisy chain a new wire with both female ends from the remaining male from horn #1 to the terminal on horn #2.



I was too lazy to deal with the tight space trying to fit both horns, I ended up using the stock location for horn #1 and used the ground bolt on the driver's inside fender (across from the brake fluid), just had to bend the horn bracket 90 degrees.
03-09-2012 09:33 AM
Matador Is there a way to avoid cutting anything off, or splicing into the stock wiring? I thought these horns were a plug & play solution. I'm always weary of messing with any electrical connection of a vehicle with a can-bus system. Understandably, these are just horns and probably will have slim affect to anything if I messed with the wiring, but I would like to avoid it if I could.
03-09-2012 09:11 AM
BillyPete I already swapped my stock horn with a bad boy wolo horn,, but you have done a top notch job with this writeup!
03-09-2012 12:17 AM
kbwwolf Wow man. Excellent writeup.

I think the stock horn was designed for the Shriner mini cars you see zooming around in parades.
03-09-2012 12:09 AM
cavejeep
My 2012 JKU Horn Upgrade Install

Thought I'd share my install of the PIAA 8511 115db 400 Hz and 500 Hz horns. I was not happy with the sound of the stock horn, almost embarrassed to use it. And I haven't seen any install guides here that I liked, so I documented my install.

This is as installed on my 2012 JKU

Items needed:
- PIAA 8511 Horns, available from multiple retailers.
- 5" of 1/8 inch aluminum bar (available at Home Depot, in 2 foot length)
- 3, 3/8" hex bolt, 1" long
- 3, 3/8 nuts
- 3, 3/8 locking washers
- 3, 3/8 washers
- 2, Wire tap connectors (I used these, bought at Home Depot Amazon.com: Quick Splice Wire Tap Connector 22-18 Gauge (Red) - 100 Pack: Automotive)

Step 1: Remove the old horn.

Step 2: Take the two wires that came with the horn, and cut off the u-shape wire connector (not the spade end that plugs onto the horn, we need that end). Use the wire tap connectors to one wire to each of the factory horn wires. DO NOT cut off the factory horn connectors, those will still be used to connect one of the horns. These included wires tapped into the factory wires will connect the second horn. This is how the instructions that came with the horns suggested to wire them.



Step 3: Find out which wire is positive. On mine, it was the grey wire with yellow strip. To check, connect a volt meter, set to measure voltage. Push your horn, and if you get a +12v, you've got the polarity right. If you get -12v, you've got it backwards. Mark the wire appropriately.

Step 4:
Cut your aluminum bar to 5" and drill holes approximately as shown below. Drill the holes just large enough for the 3/8" bolts. I also rounded of the edged, and painted it black. I also painted the nuts, bolts, and washers black too.



These pictures show how I'm going to attached the horns to the bar. The top hole on the bar is going to bolt to an existing hole in the engine bay, shown below (2nd picture).






Step 5: Bolt one of the horns to the lower, bottom hole (as noted in the first picture). Don't tighten it all the way, we'll get it lined up in place first. Note I do not remove the dust cover on the lower horn, but will on the upper horn. Also I had to widen the holes on the horns slightly to accommodate the 3/8" bolt.




Step 6: Line up the top hole on the bar with the hole in the Jeep. Place a bolt in the hole if it helps. Adjust the lower horn angled down as far as possible, to keep enough room for the second horn. Note you might want to connect the factory wires, as that may affect the position of the horn. Once your happy, carefully remove the horn and bar, and tighten that horn down good and tight.

Step 7: After tightening the first, lower horn, reinstall back in the Jeep, and connect the factory horn connectors to this horn. Connect the positive to the top connector on the horn (as you are looking at it reading the PIAA label). Connect the negative to the lower connector. Then bolt the bar to the Jeep and tighten it down.



Room for Improvement
: It may be better to move that middle hole down (or flip the bar), so that the bar can be removed without removing the top horn (or so the bar can be installed with both horns attached before hand).

Step 8: I removed the dust cover from the second (upper) horn (shown below, horn on left), as there wasn't enough room for it. Its aimed up, so should stay relatively clean. The factory horn didn't have any cover, so I figure its probably okay.



Step 9: Once the bar is attached to the Jeep, install the second horn and connectors (that were included, and tapped into the factory wires). Same rule applies on polarity, positive on the top most connector on the horn. I used some pliers to make the connectors tighter, so they wouldn't easily slip off.





Step 10: Test.

Here is a video of the difference for me:2012 JK Horn Difference.wmv - YouTube

Now you can honk without people laughing at you. Enjoy!
-mike

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:47 AM.



Jeep, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC