Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Painting Fender Flares

Join Wrangler Forum Today

Thread: Painting Fender Flares Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-04-2012 11:49 PM
Familyman22 I just did this three weeks ago. I have a 200 TJ, and my fenders were shot. All I did was buy a sandpaper sponge block, light grit, and sanded them lightly, there is no need to sand for hours, you'll just waste your time. As brown.jasonc said, dont use heavy coats, if you end up getting a run, (which I did) its realy tough to get it sanded down and look right. I had to wait or it to dry, and then sand a big spot down to try to blend it in. It sucked, so make sure you take your time, even light coats, and it will turn out great. I'm proud of mine, they look great. Krylon Fusion is about 5 dollars a can and I used 2 cans, one on each side of the vehicle.
Taping off the fenders and the tires is a great choice. Be sure to use painters tape, so that it doesn't leave any residue, and tape plenty of newspaper over the factory paint and accessories so that any over spray doesn't ruin the factory paint. I tried removing my fenders, but it is really tough, and the screws are usually pretty weathered. Best advice is take your time, mask and tape everything well, and use even light coats.
04-04-2012 10:18 PM
Originally Posted by doughenry View Post
I just used rustolem texture from lowes it cost like 6 bucks for a can.Man this stuff looks awsome!I used 220 sandpaper and all I really did was lightly scuffed on the fenders,the out come really was surprising.

You got a picture? I'm planning on doing my lady's TJ and want to see how yours turned out. Thanks.
03-10-2012 09:42 PM
brown.jasonc I just did this today, and though it took awhile, the result was worth it. I washed the area thoroughly and let it dry. Taped off the area including the tires. Then started spraying. I ended up using 2 cans and probably 5 coats. I found very early that you need to do many light coats instead of a few heavy coats. The runs and build up will be obnoxious otherwise and you will have to wait at least an hour for the paint to dry enough to sand back down again. Save yourself the time and just do light coats. It takes 15 mins to dry enough to add another coat.

Other then prep the process was really easy. Taping everything off was the worse part and even that was just time consuming, not terribly bad. Good luck!
03-10-2012 07:45 PM
doughenry I just used rustolem texture from lowes it cost like 6 bucks for a can.Man this stuff looks awsome!I used 220 sandpaper and all I really did was lightly scuffed on the fenders,the out come really was surprising.
03-10-2012 03:31 PM
Gate53 As the last guy said just get anything loose off and scuff them up a bit (not rough but not totally smooth) and use the Krylon it seems to last I'm going on two years and it still looks like new. You might grab a tack cloth to make sure all the dust is off too.
03-10-2012 03:27 PM
wwch99tj Get the loose paint off and make sure the rest is scuffed good

That's the reason I bought sahara flares I got tired of painting my old flares
03-10-2012 02:18 PM
Painting Fender Flares

I'm painting my fender flares probably tomorrow, I'm going to buy Krylon Fusion tonight. My fender flares are starting to fade a little and was wondering how much sanding i need to do before painting. Last time i sanded for literally hours, but my brother said you just have to scuff it up. Any suggestions?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 10:38 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC