Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Question about transmission mount,

Join Wrangler Forum Today

Thread: Question about transmission mount, Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2012 01:33 PM
Garyk x-2, all the locktite in the world is not going to work if the threads are dirty. Take the whole bracket off and clean out the thread holes and clean the bolts, lock tite the bolts with red (that's if you don't want to remove them anytime soon)
04-28-2012 10:39 AM
jakep U might have to drop it alil bit to get in there
04-28-2012 01:27 AM
beardown it's in a pretty tough spot to get to, really don't want to drop skid plate
04-28-2012 12:19 AM
jakep Try blue locktight spray brake cleaner to clean the gram
04-27-2012 11:01 PM
beardown was under jeep today and the damn bolts fell out again??!!! any ideas a to how to get these to stay? theres a lot of grease under there, would that prevent some kind of lock tight from working?
03-27-2012 01:10 AM
rebelBullDawg325 it was abt 3 years ago that i did mine, i honestly dont remember if it gave me any problems or not
03-26-2012 08:58 PM
beardown The tranny mount itself is good, after market poly mount which is perfectly in tact, it was the part above it that screws in to the trans itself that the bolts fall outof! That is good now, the drive shaft u joints are the prob now! As long as its ready to go for the summer!
03-26-2012 08:47 PM
Yjpower94 My old 4.0 had a bad tranny mount just ordered a new poly mount and it made a hell of a difference. I was getting alot of whacking under torque.
03-26-2012 08:32 PM
beardown Yea doin it this week, how tough is it to get the old one out? Would a hammer, sockets and a c clamp do the trick?
03-26-2012 01:16 PM
rebelBullDawg325 yes, replace the u-joint asap before it explodes on you, can cause much more damage.

easy check, grab drive shaft on each side of joint, wiggle opposite directions of each other. if there's free play, its bad. but what you described is literally the exact situation i had
03-25-2012 02:35 PM
beardown So I replaced those bolts with 8 grade and locking washers, now when I drive it I am getting this crazy and scary clunking sound ! What could this be? Im thinking that now that the transmission is more secured to the skid plate that the dying u joint is able to move more causing this clunking sound? Sounds like something's gonna explode!
03-18-2012 01:33 PM
beardown Yea the shake is getting pretty bad so I figure I better fix it before something else breaks, I just hope the threads inside are still ok!
03-18-2012 11:36 AM
rebelBullDawg325 your hardware store should have it. this seems to be somewhat common issue. i've heard of it happening before. happened to me as well and caused my ujoint to go bad
03-18-2012 11:11 AM
beardown Would the local true value carry the grade 8? Or is it a specialty auto thing?
03-15-2012 05:51 PM
beardown Cool I guess I'll go with new grade 8 bolts and lock washers ! Thanks
03-15-2012 03:04 PM
Xpress Lock washer for sure. My AX5 has a stripped bolt hole and only has one bolt holding it to the poly mount, after the original 2 bolts fell out or got yanked out. FORTUNATELY whenever I go and buy bolts like this I won't buy anything less than a Grade 8.

A grade 8 and a lock washer are all that's keeping my tranny from moving side to side. I did happen to check it a couple months after I put it in, still tight
03-15-2012 02:02 AM
beardown Yea is only the flat washers, I'll be sure to crank em down! Thanks
03-15-2012 01:25 AM
Dutch 95 Yes and Yes...those are the bolts that should be in the tranny mount, and likely the tranny moving around could definitely cause the u-joint problem. When you put the bolts back in, I'd recommend using lock washers to keep it tight. It looks like there is only a flat washer currently.
03-15-2012 01:04 AM
beardown Did it make it shake pretty good when accelerating or going up hill?
03-15-2012 12:36 AM
91yjman Yes same thing happened to me I have a 4.0 i don't know what the parts called but it is supposed to bolt to your tranny
03-14-2012 08:36 PM
beardown Few more...
03-14-2012 08:34 PM
beardown The red (now red and black) thing is obviously my poly trans mount... The question I had was if the black part above the red poly mount was supposed to bolt in to the trans itself, I guess that's the bolt that should be there eh? And maybe the extra shake caused my u joint to fail? Am I correct in this diagnosis? Thanks dudes
03-14-2012 08:31 PM
beardown Ha, I went out and reached my phone above the skid plate to take a pic of it to show you what I'm talking about and think I answered my own question cause when I looked at the pic I saw a bolt jut hangin out.....
03-14-2012 08:25 PM
Bs13855 Yes.

Do you see your tranny mount.

I don't have a tranny mount on mine and I have no issues.
03-14-2012 08:20 PM
Question about transmission mount,

I was under my 93 yj today inspecting a bad rear driveshaft u joint and noticed that the transmission slides back and forth easier than it seems like it should,,, it's the part just above my poly transmission mount, I noticed that there are holes that seem like they would attach this to the transmission itself, should there be bolts there that maybe fell off? Hope this is clear enough

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 06:57 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC