Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > help me with my computer

Join Wrangler Forum Today


Thread: help me with my computer Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-04-2008 05:02 PM
Triple88a
Quote:
Originally Posted by whitebuffalo View Post
im willing to bet it wont handle quite like its roller coaster once you drop a 302 in there.......
The entire swap only adds 350 lbs bringing the weight to about 2500-2600 lbs... meaning 302, large rims and tires to handle to torque, heavy duty springs with shocks (struts to be exact), 8.8 rear end, i think it was T5 tranny, stronger drive shaft, dual 2.75-3" exhaust from engine to rear. Stronger engine support. front and rear strut bars.
I've seen V8 conversions that pull stuff for weight reduction bringing it nearly back to stock weight.

weight distribution being F52/R48 stock and F54/R46 with the V8

Many people think the stock miata engine weights nothing as its only a 4 banger.. well that thing is pure iron lol. People add over 25 lbs of boost on stock block and it holds without a problem (obviously new crank, pistons and rods needed)

MOz i'll put one of those offroad flags for ya
04-04-2008 12:21 PM
MOz
Quote:
Originally Posted by Triple88a View Post
honestly i do man,

Taking the top down in couple of seconds, having it handle like a roller coaster around turns.. eehhh great memories. I'm planning on getting another one and rebuilding it from scratch with a supercharged or turbo charged 5.0 in it.
It's OK Trip...we'll still respect you.

However, make sure you mark it clearly so we don't accidently drive over it in the mall parking lot.
04-04-2008 08:09 AM
whitebuffalo
Quote:
Originally Posted by 4.0l sahara View Post
Ya weather it's the 2.5 or 4.0 it's a push rod valve train not a dohc. Also at high rpms the valves can start to float with the stock springs.
ding ding ding. we have a winner!

Quote:
Taking the top down in couple of seconds, having it handle like a roller coaster around turns.. eehhh great memories. I'm planning on getting another one and rebuilding it from scratch with a supercharged or turbo charged 5.0 in it.
im willing to bet it wont handle quite like its roller coaster once you drop a 302 in there.......
04-04-2008 12:12 AM
Triple88a
Quote:
Originally Posted by MOz View Post
I think Trip still misses his Miata.

Trip...It's OK you have a Jeep now ..It's time to let go.
honestly i do man,

Taking the top down in couple of seconds, having it handle like a roller coaster around turns.. eehhh great memories. I'm planning on getting another one and rebuilding it from scratch with a supercharged or turbo charged 5.0 in it.
04-03-2008 04:22 PM
Tj Bunch
Quote:
Originally Posted by MOz View Post
I think Trip still misses his Miata.

Trip...It's OK you have a Jeep now ..It's time to let go.
Moz when I worked at mazda we Called them Pinata's Couse there soo small.
04-03-2008 11:10 AM
MOz
Quote:
Originally Posted by Barrie in Maine View Post
The 4 cyl, if that is what he has is a good little motor if left stock and taken care of. The 4 in your Miata is a whole different beast with a lot of potential if done right and capable of turning high revs all day. Oh well it's his motor.
I think Trip still misses his Miata.

Trip...It's OK you have a Jeep now ..It's time to let go.
04-03-2008 09:45 AM
dweebster
Quote:
Originally Posted by 4.0l sahara View Post
He wants to raise the rev limiter from the stock 5300 or so to 6000. Waist of time it's not like your little 4 cylinder that will rev up to 7k. This isn't a high reving engine and it would see no gain in doing so and also after a while you may throw a rod or somthing because it isn'nt designed to rev to 6k.
why you have hate on a 4 banger LOL! i got to rep mine! as for the thread. . . grammar? LOL
04-02-2008 09:15 PM
Smeghead I've dynoed so many cars I can tell you for sure without a collosal amount of mods and probably an engine change your going to be way out of the power band much over 5k on a stock TJ let alone pushing it higher
04-02-2008 08:32 PM
4.0l sahara I like how he says hyperteach.
04-02-2008 08:01 PM
Triple88a
Quote:
Originally Posted by orange05tj View Post
I think Debruins has some competition now.


too bad he only has 2 posts though
04-02-2008 07:37 PM
orange05tj
Quote:
Originally Posted by WrAnGlEr View Post
hii...............
i'm facing proplemwith my computer i have drid the hyperteach and it didnt work
i wont to increes my rpm to 6000 but i dont no how i have trid every thing but it didnt work well i have burn 2 computer until now
i have tj 1997 with volant intake and full borla exuset and msd and camsaft( crower)
so plz help me with it

thnx
I think Debruins has some competition now.
04-02-2008 07:24 PM
4.0l sahara Ya weather it's the 2.5 or 4.0 it's a push rod valve train not a dohc. Also at high rpms the valves can start to float with the stock springs.
04-02-2008 07:11 PM
Barrie
Quote:
Originally Posted by Triple88a View Post
Well he already got the rest of the mods to help the high end and the chip helps with the needed fuel.. if the chip allows it to reise fuel cutoff to 6k.. thats just an extra.


back when i had my miata (4 banger) people made those things rev to 12k. With some straight pipes at that rpm those motors will give you a hard on.
The 4 cyl, if that is what he has is a good little motor if left stock and taken care of. The 4 in your Miata is a whole different beast with a lot of potential if done right and capable of turning high revs all day. Oh well it's his motor.
04-02-2008 07:10 PM
4.0l sahara It's really not worth it because the stock porting will not flow very well at high rpms. Also the stock cam isn't the proper lift/duration and overlap to produce power at high rpms. Even the cam he has isn't going to make power at 6k.
04-02-2008 07:07 PM
4.0l sahara If you read I said it isn't like your normal ohc 4cylinder. That most 4cylinders can do 7k with little or no mods except for the rev limiter raise. Also if he really wants to raise the rev limiter I would say 5500 would be okay.
04-02-2008 06:55 PM
Triple88a
Quote:
Originally Posted by Barrie in Maine View Post
I agree it won't blow at 5,201 it wont blow at5,301 for that matter. But don't these motors 4 or 6 cyl, make there power on the low end and any time or money spent getting it to rev to 6 or higher be wasted for very little gain? idk
Well he already got the rest of the mods to help the high end and the chip helps with the needed fuel.. if the chip allows it to reise fuel cutoff to 6k.. thats just an extra.


back when i had my miata (4 banger) people made those things rev to 12k. With some straight pipes at that rpm those motors will give you a hard on.
04-02-2008 06:50 PM
rthdtj KaaBoom......knocknocknocknocknockBBBBBshshshshsBB BB________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ __________________________________________________ _________ DAMN
04-02-2008 06:42 PM
Barrie I agree it won't blow at 5,201 it wont blow at5,301 for that matter. But don't these motors 4 or 6 cyl, make there power on the low end and any time or money spent getting it to rev to 6 or higher be wasted for very little gain? idk
04-02-2008 06:33 PM
Triple88a
Quote:
Originally Posted by 4.0l sahara View Post
He wants to raise the rev limiter from the stock 5300 or so to 6000. Waist of time it's not like your little 4 cylinder that will rev up to 7k.
where did he say he had a 4 banger?

Quote:
Originally Posted by 4.0l sahara View Post
This isn't a high reving engine and it would see no gain in doing so and also after a while you may throw a rod or somthing because it isn'nt designed to rev to 6k.
The cold air intake and the free flowing exhaust help in the high rpms. Also just because Jeep limited it at 5200 doesnt mean you cant rev it higher. It will not explode at 5201rpm.. trust me on this

How about looking at it this way
Your jeep came with 17" tall coils in front.. why are you running longer ones?
04-02-2008 06:32 PM
Tj Bunch Dam it Smeag, Sugar coat it why don't you.......LoL
04-02-2008 06:15 PM
Smeghead I knew exactly what he was saying, hes ricing up his Jeep and he now wants a VTEC with the ability to rev to 8500rpms.
He basically wants to hack his computer to remove the rev limiter which it sounds like hes tried and blown several up which is actually fortunate because if they didnt blow he would blow his engine

Sorry if I though it was a joke, guess your just stupid
04-02-2008 06:02 PM
4.0l sahara He wants to raise the rev limiter from the stock 5300 or so to 6000. Waist of time it's not like your little 4 cylinder that will rev up to 7k. This isn't a high reving engine and it would see no gain in doing so and also after a while you may throw a rod or somthing because it isn'nt designed to rev to 6k.
04-02-2008 05:15 PM
Triple88a
Quote:
Originally Posted by Barrie in Maine View Post
I have read this again, and I think he might be talking about his TJ computer and he is trying to get the motor to go above 6000rpm. jmo?
you might want to read it again.. it says it wont increase the motor TO 6000 rpm

With the extra fuel added by the chip, i dont see the problem of getting a fuel cutoff limit at 6k instead of 5200.

also what do u mean by "burn 2 computer"?

you might want to call hypertech and ask them for help.
04-02-2008 05:05 PM
Barrie I have read this again, and I think he might be talking about his TJ computer and he is trying to get the motor to go above 6000rpm. jmo?
04-02-2008 04:55 PM
gus54
Quote:
Originally Posted by WrAnGlEr View Post
hii...............
i'm facing proplemwith my computer i have drid the hyperteach and it didnt work i wont to increes my rpm to 6000 but i dont no how i have trid every thing but it didnt work well i have burn 2 computer until now
i have tj 1997 with volant intake and full borla exuset and msd and camsaft( crower)
so plz help me with it

thnx
Mebe yuo shud tak it bak to tha coputer guy yuo bote it frum.
04-02-2008 03:34 PM
Barrie
Quote:
Originally Posted by Smeghead View Post
Im assuming this is either a joke or your an idiot
Gotta be a joke!
04-02-2008 03:11 PM
Smeghead Im assuming this is either a joke or your an idiot
04-02-2008 02:39 PM
WrAnGlEr
help me with my computer

hii...............
i'm facing proplemwith my computer i have drid the hyperteach and it didnt work
i wont to increes my rpm to 6000 but i dont no how i have trid every thing but it didnt work well i have burn 2 computer until now
i have tj 1997 with volant intake and full borla exuset and msd and camsaft( crower)
so plz help me with it

thnx

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:43 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC