|Today 12:31 PM|
|Jenkins01||Installed AFE Momentum GT Cold Air Intake... Simple install, great results! Obvious increase in acceleration, and even sounds better!|
|Today 12:15 PM|
|pepatrick||Speaking of...Mr. Brown Santa just showed up and sPod is in hand. Looks like it is time to take the rest of the day off.|
|Today 12:00 PM|
|pepatrick||Waiting patiently for sPod to show up..Come on UPS...|
|Today 09:54 AM|
|PrecisionPowder||Ordered a cobra 75 wx st today with a firefly 4ft antenna and a quick disconnect. Just need to build a simple bracket when it gets here to mount on my 3rd tail light, get an external speaker locally, and I will be ready for vacation.|
|Today 07:27 AM|
|relyt||I stayed up late this morning to get my hood blackout put on finally. Hopefully it'll be cured on there good enough to be able to safely drive when I wake up this afternoon.|
|Today 06:39 AM|
Ace Sliders - fitment question
Got a surprise from the brown Santa truck when I got home yesterday, a key ring with bottle opener from Ace Industries! Lucky for me it came with 2 Rock Sliders, lol!
Didn't go on as slick as the video, but still was little effort, ended up grinding the entire circumference of the body mount washers as the where just a smidge to large for the hole, no big deal. the look great and are sturdier than I expected, impressive.
I have one question for you guys, the driver side fits perfect, the passenger side rear hits the Rubicon slider hard. If I had another large washer I'd place it between the slider and the frame mount. I can see friction wear to happen between the Rubi rail and Ace rail as the contact is solid and hard.
Have anyone seen this before and should I be concerned?
|Today 06:10 AM|
Went crawling at Tuttle Creek ks on Sunday, took a good bounce dropping of a rock ledge but no damage to the muffler.http://youtu.be/ZvQikTG4Gm0
|Yesterday 11:41 PM|
|ofwiv||I ordered some new 17x9 KMC XD 122 Enduro wheels in solid black with some Mastercraft 33" tires for my 2014 Billet Silver JK Unlimited. They are being installed tomorrow!|
|Yesterday 11:34 PM|
So had some time and money out on a job right now had to do something to kill some time and wanted it to be something needed..
Made some reinforced 3/16" rear lower control arm mounts to weld over mashed stock ones...
Made 3/16" plate mounts for lower control arms...along with a skid...the backplate isn't in the pic...forgot about it on table..
This side was good back side was crumpled in and other side was mashed heavily
Boxxed in the rear upper as well, there will be a triangular gusset going downwards added.
Plated the lower heavily ground off the stock angled at frame and burnt this in
And here's a shot on...
Got some RCV's from a buddy so finally slapped em in...
Slapped the rear carrier back in and added a bar on top that will also be a LOW profile rack that rotates up to allow tops off and on easily.
|Yesterday 11:25 PM|
|Higgs82||Had a hitch installed, next toy o gt is going to be a camper, cant wait|
|Yesterday 11:24 PM|
|Yesterday 10:27 PM|
Don't know if I posted this before, but I'm gonna do it again anyway (hmph)
Plastidipped the grill red and the hooks. New steel bumper (going to get the bars after I do the suspension).
Realized way later that I didn't even have to tape the stupid billet! Doh!
|Yesterday 10:24 PM|
|Yesterday 09:55 PM|
Installed a 21" light bar from SuperBrightLED's
|Yesterday 09:47 PM|
|Yesterday 09:41 PM|
did you paint yours? plastidip? or order replacement hinges?
do you have a close up picture?
|Yesterday 09:36 PM|
|Das_K||Added Rigid light bar and side lights.|
|Yesterday 09:25 PM|
|Yesterday 08:45 PM|
|PrecisionPowder||Got my cheap HF hitch rack it. Wobbles like crazy so I am going to have to sleeve it or weld some thin plate to the receiver to stop that|
|Yesterday 08:22 PM|
|WranglerAddict||Just sat in the driveway and admired it while drinking a cold one and watering the front yard!|
|Yesterday 08:15 PM|
|Yesterday 07:57 PM|
|lingle80||Dropped mine off at the dealer to have the hard top wiring harness installed|
|Yesterday 07:54 PM|
If anyone is interested in winning a complete new 3.5" lift kit, check this link out!
|Yesterday 07:45 PM|
|Yesterday 07:43 PM|
|Yesterday 07:38 PM|
If yiu ever wheel you'll wish for that lift. Then cones 35's and then 3.5 inch lift then 37's
|Yesterday 07:37 PM|
|Yesterday 07:35 PM|
|Yesterday 07:29 PM|
I would say if you don't ever have this issue, then maybe you don't need the lift... But if you do any wheeling and start scrubbing, you may damage a tire.
Those do look really nice!
|Yesterday 06:59 PM|
Had my buddy who owns a performance shop order new gears today, going with 4.56's. Was going to order from a vendor but by going through him I got a unbeatable price on both parts and labor.
Also ordered a SPod for the LED lights I'm going to order soon.
|This thread has more than 30 replies. Click here to review the whole thread.|