Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > What lift do I have?

Join Wrangler Forum Today


Thread: What lift do I have? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-22-2012 02:52 PM
bigskycountry0329 Thanks Beachcruiser, that is encouraging. The 6 pack will definatly help persuade them to check it out for me.
03-22-2012 02:50 PM
Beachcruiser The shop in my area is staffed w/ some pretty cool people, they don't mind poking their head under & giving an opinion for free. Maybe I'm lucky, but the Jeep/4X4 community around here is pretty tight and constantly support one another w/ advice & skills. Many local boards have forums for listing positive reviews of suppliers/shops. You might be surprised.

Of course, it helps if you show up at quitting time on Friday w/ a cold 6 pack or two....
03-22-2012 02:35 PM
bigskycountry0329 I did think that maybe the shaft is out of balance. I will have the shop that made it ensure that it is balanced correctly. I would dimiss the the yoke bearings since they did not vibrate before the the upgrade, although they could have gone out with the excessive vibes when the pinion angle was off. I also have new U joints installed on the shaft. I have been trying to avoid the shop but that may be what I am stuck with doing.
03-22-2012 11:49 AM
Ibuildembig If you dont want to lower the case, you can cut and roll your rearend. This one of the reasons I hate CV shafts....they are picky, expensive, and not as strong. Personally lowering the case doesnt bother me, if one inch hangs you up....your probably where you dont need to be in the first place
03-22-2012 10:49 AM
Beachcruiser One of the reasons to install an SYE/DC shaft is to NOT have to drop your TC/skid plate. I'd think you could eliminate the vibration w/ adjustment of the pinion angle...unless something is jacked up w/ the shaft or yoke bearings. Might want to get a professional shop to give you their opinion.
03-22-2012 10:18 AM
CharTay You probably need a tcase drop
03-22-2012 10:10 AM
bigskycountry0329
What lift do I have?

Despite looking dumb I will ask anyways. I am not ceritan of how much lift I have. What is the best way to find out how high my suspension lift is?

The reason I am concerned is because I have bad drive shaft vibrations on the rear drive shaft. I installed an AX-15 with SYE (bye bye peaugot). I had a custom drive shaft made. I know the double cardon requires a zero degree angle between the drive shaft and pinion. I seperatly installed 2.5 degree spring perch shims and then 4 degree shims. The 2.5 degree shims helped more than the 4 degree shims. The 2.5 degree shims bring the angle to just about zero.

Should I install some washers on the skid plate to lower the TC? Oh yeah, I installed an advance adapter mount plate for the peaugot to AX15 upgrade, which raised the TC about 1/2 inch.

Should I worry about how high my lift is (bought it with the lift), in relation to the driveshaft vibes?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:49 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC