Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Stability Control Issues After 2.5 BB Install

Join Wrangler Forum Today

Thread: Stability Control Issues After 2.5 BB Install Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-27-2012 09:50 AM
Tim223 I must have screwed up getting everything recentered and level..there's a local guy that knows JKs real well, I'm gonna have him take a look at it...CJs are way easier to deal with by the way.
Thanks for all of the input, I will update this when it is all figured out.
03-26-2012 05:39 PM
actualsize I just installed a 3" Mopar/Teraflex lift kit. On my first test drive this happened before I re-centered the wheel (I couldn't wait.) And yes, it only happened in one direction. It stopped as soon as I re-centered the steering wheel. It doesn't take much. 5 degrees or so is enough.

When re-centering the steering wheel it is important to do it at the drag link (which is the easy way, anyway). Popping the steering wheel off and re-indexing the spline is no good because that messes up the zero point of the steering angle sensor.

03-26-2012 05:24 PM
kbwwolf Another vote for steering not being centered. If it is, maybe mud on the inside of your wheels, or a clockspring problem?

Clockspring issues crop up here from time to time. Usually causes ESC or ABS lights to activate.

Even if your caster is into the dreaded negative numbers range, that shouldn't by itself cause ESP probs.
03-26-2012 05:10 PM
Tim223 It's level, this is starting to get frustrating…thanks for the help so far though.
03-26-2012 04:12 PM
Tim223 You have me thinking, I can't say off hand if it is only happening when I am turning right..I have mostly been noticing it on exit ramps so that might be it, I will have to make sure it is level. I can't think of why it wouldn't be, but there is clearly something going on. Thanks for the idea.
03-26-2012 03:56 PM
Revyjku08 My guess would have been the steering wheel as this had to be adjusted everytime I added a lift to stop the ESP from kicking in. The only other thing is if the lift is leaning more to one side and the ESP is kicking in as the computer believes you are cornering too fast and thinks it is going past that tipping point to prevent a roll over????
03-26-2012 03:23 PM
Tim223 I'll have to check the caster tonight..I have spoken to a few people that have gone with the same set-up though and haven't had any issues since it's just a 2.5" boost. Thanks for the response though, I'll be sure to check it.
03-26-2012 11:37 AM
kjeeper10 LCA's... Caster too low

I should have said adjustable CA's

Another option would be AEV correction brackets to relo the stock CA's
03-26-2012 11:26 AM
Tim223 Yes on both, those were my first two guesses, but everything is where it should be..thanks though.
03-26-2012 11:04 AM
4fit Did you recenter your steering wheel after the lift install? Need to make sure it is dead center and also that the axle is properly centered.
03-26-2012 11:01 AM
Stability Control Issues After 2.5 BB Install

I just installed a 2.5" Teraflex BB with an adjustable trackbar and put 35" tires on my 2011 Rubicon (2 door). Since it has been on my stability control has been kicking on every time I hit an on-ramp and even on winding roads (even at low speeds, 20-25 mph). The speedo was recalibrated and everything has been double checked and looks right. Has anyone else ran into this issue or have any ideas

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 05:09 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC