|04-02-2012 11:11 AM|
Brakes and rotor are easy once you understand what to do - If you haven't found Stu's site you should check it out. It has an amazing amount of info and pics. Here is a link for the front brakes
Front Brakes Overhaul - 1
Go for it - once you've done it you'll never pay someone again.
|04-02-2012 09:18 AM|
I've always just opened the zert (sp?) and squeezed the fluid out and then bled the brakes afterwards. I'll be trying it this way the next time I do brakes on a vehicle. Sometimes the simplest solutions are the best, right?
|04-01-2012 09:11 AM|
|kshaws21||Thanks for all the input guys, will definately attempt it...|
|04-01-2012 08:44 AM|
check out this link.... -Warped- Brake Disc and Other Myths
you need to de glaze and re-bed the pads.
|04-01-2012 01:52 AM|
Remove the wheel.
Remove the two bolts that hold the caliper - not allen but 13mm wrench. This could differ between years. Swing the caliper and pads out - top first.
Once the caliper is off you can replace the rotors.
Remove the cap from the brake fluid reservoir so that you can push the piston in the caliper back. I usually stick a wrench between the two old pads and hold steady pressure till the piston is flush with the caliper for easy install of the new pads - always install new pads with new rotors.
|04-01-2012 12:15 AM|
|Cole 33||My brakes are pulsating right now a little and I've read that that could mean that my rotors are getting warped and need replacement anyone know anything about this? Sorry for the hijack. Btw i don't have anti lock brakes so that's not the pulsating lol|
|04-01-2012 12:09 AM|
|y0diggity||So apparently you might be able to get the calipers off without any problems. I've not had that experience, but it'll be awesome if you do. Either way, its an easy job. Seriously, just go for it and enjoy the time with your Jeep. :-)|
|03-31-2012 05:19 AM|
|malexii||I just changed my rotors last weekend on my 2000. I had to use a puller, heat and a hammer to get it off. They were stuck big time.|
|03-31-2012 01:09 AM|
|03-30-2012 12:38 PM|
Yeah you have to make room for the new rotor's thickness, compared to the old one.
And one more thing, after you have it all back together, and before you even move the Jeep, go in and pump the brake pedal a few times.
If not and you forget too, you will have a certain portion of your anatomy clench up as you hit the brakes and the pedal goes to the floor.
|03-30-2012 12:20 PM|
All I do is pull the cap off the master cylinder (to avoid any pressure build up) and then take a big enough c-clamp and use that to push the cylinder back in. I've never had to drain fluid or ever had to bleed the brakes after doing pads and rotors. Keep the old brake pad on the cylinder and put the clamp against that. Screw it nice and slow until it seats all the way down and you'll be good to go. Once you're done, don't forget to put the cap back on the MC.
|03-30-2012 11:26 AM|
|03-30-2012 11:23 AM|
|DevilDogDoc||Just grab the caliper after its unbolted and rock it back and forth that should loosen it up enough to get it off the rotor. Then slide the rotor off the hub.|
|03-30-2012 11:16 AM|
You'll have to let some fluid off of the cylinder in order to get it to let go of the rotor (usually), so you'll probably need to bleed them again. On my '06, the caliper bolts are just standard bolts, not allen, but I'm not sure about an '00. It's super easy, seriously.
*addidition* I don't think there should ever be a need to detach the brake line when performing routine maintenance on your brakes. Again, someone here can keep me honest if I'm wrong, but I've not had too.
|03-30-2012 11:03 AM|
|kshaws21||Thanks, does the brakeline have to be removed and rebled or does it just stay attached to the caliper inntact?|
|03-30-2012 10:58 AM|
5 nuts for each wheel, and two bolts for each caliper. Then the rotor should slip off. there might be retaining clips on 2 or 3 of the studs, but they should come off easily.
Also I believe the caliper bolts use an allen wrench instead of a socket.
|03-30-2012 10:57 AM|
|ebigham1||I never did one on a jeep but on everyother car is easy. Just take off the tire remove the brake assembly and the rotors just come off.|
|03-30-2012 10:51 AM|
how hard to replace rotors?
How difficult is it to replace front brake rotors on a 2000 TJ for someone who has never done that? I recently had pads put on and had em bled so that part is ok. I just need to put new rotors on soon and was wanting advice. I'm somewhat mechanically inclined, just have never changed rotors myself.