|01-21-2015 07:26 PM|
|01-21-2015 07:14 PM|
|KerriCagney||My TJ has padding also, what did you adjust the numbers to?|
|01-11-2015 10:08 PM|
|Jeep maniac||The girlfriend and I just got done making these. We did red and black at first and It just didn't match enough for me so ended up going all black. Had to adjust the numbers a bit to fit the padding|
|01-11-2015 09:04 PM|
I had to mess around with the original numbers for my jeep but so happy with the outcome!
|12-22-2014 11:31 PM|
|TacticalDan||So glad I found this thread. So far, I've wrapped the grab handle in front of the front passenger seat, and created grab handles for the two front seats as well as two attached to the back of the front headrest. I was able to put the fronts in a spot that's a better location (corner attached to A Pillar) than the stock Mopar ones that came with the Jeep. I left the stock ones in the back, the paracord ones are simply supplementary. However, I am probably going to get a few more shackles and replace them as well.|
|12-20-2014 12:56 PM|
|MangoTangoT||I think I'm going to make some in the next couple weeks for my jeep! Thanks!|
|12-19-2014 07:49 AM|
|xthng1||Know this is an older thread but thinking this might be the first project. Thanks to everybody for the info.|
|11-14-2014 01:46 AM|
Just did the back for now to work on my technique...pretty easy to do with your guide OP! Thanks!
Made them all 11" long which equated to approximately 45" of core. Then cut pieces into two 5' and melted together for cobra weave.
Core- ACU Digital Camp
Wrap- OD Green and ACU Digital Camp
My JKU is Silver, and I like OD. The colors went well together and with Jeeps colors. Next I'll tackle the front, but for now the back was needed for the kiddos!
|11-04-2014 05:19 PM|
Just put mine in. They were very easy to make. Also made handles for the headrests too. Thanks for the instructions!
|10-05-2014 12:28 AM|
|Irish-n-Zwack||I know this is an old thread, but I just wanted to thank the OP for his instructions. I needed grab handles badly, and my husband, Zwack, used this thread to make the first one just last night (for the driver's side, where I usually sit). Mine is red and retro-reflective orange. I've already put it to good use. Number two will be made and added to the passenger side, soon. Thanks again!|
|08-14-2014 08:11 PM|
|Senayski||Other side goes under a bolt on the side of the sun visor!|
|08-14-2014 10:10 AM|
|08-11-2014 09:04 PM|
|Senayski||Nevermind. Figured it out|
|08-11-2014 05:26 PM|
I ordered a pair but onlt one side had the ring and loop to go around the frame of the jeep.. Any suggestions??
|08-08-2014 09:37 AM|
Don't mind the rollbar padding....PO didn't understand how things go together. I've got to take the windshield bars back off so I can fix that.
|08-08-2014 09:23 AM|
Here's mine; installed this morning!
Thank you for all the good information on this thread.
I went with a 4-core Cobra weave. I made the cores from black cord, then used a blue digi-camo and tangerine orange. Got them from Paracordgalaxy.com which has sooooo many colors to choose from. Making the cores black really pops the color out; see the comparison pic here between that and a standard 2-color key fob.
I found I needed 44" of cord for the rollbar wrap cores in my JKU, and I went for an 8" long handle which required 32" of core. Colors required 5 feet each for the wraps and 4 feet for the handle. (I cut 5.5' and 4.5' respectively and had plenty left over)
|07-08-2014 07:54 PM|
|07-07-2014 08:04 PM|
|07-07-2014 06:18 PM|
|Fyer||The sizes used in the original guide were too short for me to use with the padding on my roll bars on my jk. I extended the length to 44 inches for the bar core and it was perfect. For the wrap 50 inches of each color will work fine. The handle core is still good of course.|
|06-17-2014 08:28 AM|
|06-10-2014 05:07 PM|
|RAWRChrissy||Hi there! I recently bought a Jeep JK and it came with no grab handles. Being 5'1", I have a very hard time getting into something so high. I did some research and thought the paracord handles were so cool, so I decided to try and make my own. I just finished my first handle and thought I would share!|
|03-29-2014 08:39 PM|
|03-29-2014 08:37 PM|
My latest endeavor with paracord
A sort of harness for my subwoofers since they slide around so much on the slush mat in the cargo area. Unfortunately I didn't have enough purple leftover after grab handles like I thought I did so I have to buy more tomorrow but here's it like 2/3 finished
Even had some help from Cobra puppy
|03-27-2014 01:11 PM|
But hey have a leash if I get another one
|03-27-2014 12:27 PM|
I'm going to be making straps to hold my subs down (they came with it)
They keep rolling around and it's annoying as hell and I figured I needed to incorporate the black and purple thing all the way through my jeep lol
|03-23-2014 05:18 PM|
|4x4mickey||OK the leash is posted in my jeep profile can't get it to load them in to the thread but shows the idea|
|03-23-2014 04:13 PM|
|4x4mickey||well i have it made, now just need to get this thing to allow me to post a photo of it|
|03-22-2014 04:34 PM|
|03-22-2014 03:47 PM|
Post pics when you're done
|03-22-2014 03:38 PM|
|4x4mickey||Im working on a dog leash right now that will wrap the roll bar and then hook to her but be short enough she won't hit the ground in the event she tries to jump it will just put her back in the seat. and be strong enough i can put her on it as a primary lead when out of the jeep in the trail also.|
|This thread has more than 30 replies. Click here to review the whole thread.|