Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Teraflex Front Lower Bump Stop

Join Wrangler Forum Today


Thread: Teraflex Front Lower Bump Stop Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-05-2012 07:28 PM
Dick Blonov
Quote:
Originally Posted by OH9JK View Post
Personally I used hockey pucks for my lower bump stops.


DB
04-05-2012 06:26 PM
Twisky Thanks man. I guess the hockey pucks woulda been A LOT cheaper.
04-04-2012 06:42 PM
OH9JK I borrowed these photos...I think this is a TJ but same principal.

The bolts should be self tapping. You will drill a slightly smaller hole than the diameter of the bolt. If they're not self tapping then just drill hole same size a bolt and secure with a nut.

Personally I used hockey pucks for my lower bump stops. They were like two bucks each from the sports store. They are exactly 1" thick and can be stacked if needed.
04-04-2012 04:52 PM
Twisky Thanks bud
Did you you take them your self? What about the bolts?
04-04-2012 08:03 AM
OH9JK

04-03-2012 09:44 PM
Rooster454
Quote:
Originally Posted by kjeeper10 View Post
They should have supplied a tool ??

We got them out to install my spacers but could not get back in. Tool was at the house.
yep. the hardest part for me was getting the nut in there while keeping it level and getting it to catch on the threads and start screwing onto the bolt. such a pain
04-03-2012 09:36 PM
kjeeper10
Quote:
Originally Posted by Rooster454

haha it probably took me 15-20 per side to get them on. I almost gave up many many times
They should have supplied a tool ??

We got them out to install my spacers but could not get back in. Tool was at the house.
04-03-2012 09:31 PM
Rooster454
Quote:
Originally Posted by kjeeper10 View Post
That's why they are still in my center console lol
haha it probably took me 15-20 per side to get them on. I almost gave up many many times
04-03-2012 09:19 PM
kjeeper10
Quote:
Originally Posted by Rooster454

yes the rear. and it is a bitch to get in unless you have baby fingers
That's why they are still in my center console lol
04-03-2012 09:14 PM
Rooster454
Quote:
Originally Posted by kjeeper10 View Post
I forget but .... Either the front or the rear there is a hole. TF supplied a spring retainer that bolts through it.
Forget what side.
Believe it is the rear ?
yes the rear. and it is a bitch to get in unless you have baby fingers
04-03-2012 09:06 PM
kjeeper10 I forget but .... Either the front or the rear there is a hole. TF supplied a spring retainer that bolts through it.
Forget what side.
Believe it is the rear ?
04-03-2012 08:59 PM
Rooster454
Quote:
Originally Posted by kjeeper10 View Post
Ya... that is odd.

My rears are bottoms, fronts top

You have absolutely no space to put that block.
I agree. Not only no space, but what would it bolt to ?

I went out and checked mine and can't see any way that it would bolt to anywhere on the lower coil seat unless you drilled a hole in it like there is in the rear where the retainer plate goes in the spring
04-03-2012 08:56 PM
kjeeper10 Ya... that is odd.

My rears are bottoms, fronts top

You have absolutely no space to put that block.
04-03-2012 08:52 PM
Rooster454
Quote:
Originally Posted by Twisky View Post
I was told by others that 'my stock uppers are fine' and to get lowers.
It somehow bolts into the coil on the bottom
Gotcha. I don't know what to tell you man. Hopefully someone else knows more than I
04-03-2012 08:45 PM
Twisky I was told by others that 'my stock uppers are fine' and to get lowers.
It somehow bolts into the coil on the bottom
04-03-2012 08:31 PM
Rooster454 Mine came with upper bump-stops. I don't know where the ones you have would fit honestly.

These are what came with mine. You pull the factory upper ones out, put these in there and then put the factory ones up inside the TF ones
04-03-2012 08:05 PM
Twisky
Teraflex Front Lower Bump Stop

Can anyone explain how to put these on? Maybe with pictures? I cant find anything anywhere.

(Lift isn't on yet, I wanna get all my ducks in a row before install)
This didn't come with any nuts or bolts or anything. Shipped from the Q

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:17 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC