|04-15-2012 09:21 PM|
|white93YJ||i have a question? if i run 4.88 gears front and rear how fast will i be able to go in the sm 465 transmission. im affraid it will not be fast enough. would i be better off getting a different tranny with some type of overdrive?|
|04-07-2012 12:36 PM|
|darkproximity||if yours is stock which it most likely is, then you have a hp d30, you can tell by looking at the side.. look at your rear axle compared to your front, see how the driveshaft connects higher on the axle in the front than the rear?|
|04-07-2012 11:08 AM|
|white93YJ||how can i exactly tell if i have a hp d30. is there a plate or number that i can look at on the axle.|
|04-05-2012 07:40 PM|
|04-05-2012 03:38 PM|
Also it has to do with deflection. In a high pinion front end the pinion gear while under load is being forced into the ring gear where the teeth have the most material, in a low pinion front end when under load, the pinion is being pushed away from the ring gear causing the teeth to engage towards the ends where there is less material
|04-05-2012 12:14 PM|
|04-05-2012 12:07 PM|
|04-05-2012 12:07 PM|
you should already have an hp d30....
a blazer would work too. ideally for the 4.3 you want the vortec motor.
|04-05-2012 12:04 PM|
i thought about just finding a low mileage s-10 and buying it, then i would have the motor and the wiring harnes and everything but the more i think about it im gonna pass on this and just find a salvage yard that has all the stuff i need.
I'm gonna start looking for the 8.8 and hpd30 axles soon. is there anything in particular about those axles i need to look for.
|04-04-2012 11:35 PM|
|Ibuildembig||I say V8 it and be done....a V6 isnt gonna be any cheaper or better on gas. If you wanted a 6 you could do a 4.0 swap, but your gonna need a pretty extensive list of parts to make it work right (and look like it was supposed to be there)....anyone can cobble some crap together, it takes a craftsman to make it look like it was made there in the first place. For just a 33-35 you can get away with the front axle, and I am with everyone else on the 8.8. But in my true to self approach I say go big or go home lol....everything I own has a 60 front in it, I have a sick fetish I suppose.|
|04-04-2012 10:24 PM|
|Timberwolf||you could also look for a 4.0 wrangler with rusted out tub or frame for cheap and swap everything over then spend on the rear axle and selectable lockers|
|04-04-2012 10:05 PM|
|white93YJ||thanks guys this is the kind of info i am looking for, and affirmination of the project. Im gonna start looking for this kind of stuff at salvage yards.|
|04-04-2012 08:07 PM|
And with a 4.3 the list of Mods. for power is very long.
|04-04-2012 01:27 PM|
I say go for it.
4.3l vortec v6, with sm465trans, 231 tranfer case, 8.8 ford rear with locker, hpd30 with locker. gear it at 4.88.
The lockers are optional if your gonna street drive it.
way less than 10 k there so the rest on fun stuff.
|04-04-2012 12:07 PM|
YJ Rebuild... need opinions for parts??
ok guys here's a little back ground info. Ive got a 93 yj, 2.5L, manual transmission, stock suspension. 193k miles and alot of centimental value invested
I would like to rebuild the jeep i have. I know it is easy to say sell and buy what I am wanting but I would like to do this rebuild with my father-in-law that has a custom rod shop. I am looking to put in whatever I need to run 33"-35" tires, and plan to do a spring over axle conversion also.
I have another vehicle to drive but will eventually make this my daily driver after the build. I would like to go with a 6 cylinder motor idealy. so the question is if you had about $10k to invest in this jeep what performance mods would you make?
I hope to get most parts from a salvage yard at all possible, and ease of being able to work on, please, keep that in mind for what I need to be searching for. I plan on getting all hardware and supplies before the build so lets talk about what parts we need to be looking for.
and as people reply could we list pros/cons of specific parts
Motor with transmission and transfer case???
Anything else imaginable?