Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > cant seem to get my doors off

Join Wrangler Forum Today


Thread: cant seem to get my doors off Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-08-2012 10:48 AM
Another Guy In A Jeep
Quote:
Originally Posted by Mike_3303

A friend of mine did that and slightly bent the bottom of the door. Thats why i took the hinges off. Painting them was easier than getting a dent out of the door.
Ur suppose to run a piece of wood along the bottom and keep the jack near the hinge at the bottom and u won't bend the door
04-08-2012 05:40 AM
Yakjeep
Quote:
Originally Posted by Mike_3303 View Post
Had to take the hinges off the body of my jeep and use a hammer to get the hinges off the door. then used grease when i put them back on.
After 2 days of penetrating oil this is what I also had to do.
04-07-2012 08:22 PM
Wesboy Has the bottom hinge on the bodywork moved at all?
It's easy to tell if it's moved because there's different paint under the hinge and you will see a 'wedge' of different colored paint showing near the hinge.
It would be unusual for the hinge to get out of alignment but it can happen.
Mine always goes out of alignment when I've been running the tube doors for a month or two. The tube doors refuse to come off until I re-straighten that bottom hinge.

I'ts excrutiatingly difficult to get the doors off if the bottom hinge has shifted. In which case, get a Torx T40 to loosen the hinge slightly (being extra careful not to strip it - those suckers are on tight) then re-align it before attempting to remove the door.

If there is no wedge of different colored paint showing - meaning the hinges haven't moved - don't mess with them.
04-07-2012 07:24 PM
Jerry Bransford
Quote:
Originally Posted by 1quick1 View Post
Yea soak in wd-40 and use a floor jack and wood block.
Using a floor jack to lift the doors up is a good way to bend the doors or where the hinges bolt in place. Lubing and working the hinges is enough to remove the doors. If you need a floor jack to get them up and off, they aren't readly to be removed yet... more lube and give it more time to work in.
04-07-2012 06:00 PM
aveisone I just use a 2x4 like a pry bar. Stay as close to the hinge as possible. Works great.
04-07-2012 04:27 PM
Mike_3303
Quote:
Originally Posted by Another Guy In A Jeep View Post
This is what I did.
A friend of mine did that and slightly bent the bottom of the door. Thats why i took the hinges off. Painting them was easier than getting a dent out of the door.
04-07-2012 04:25 PM
Another Guy In A Jeep
Quote:
Originally Posted by 1quick1
Yea soak in wd-40 and use a floor jack and wood block.
This is what I did.
04-07-2012 04:21 PM
Mike_3303 Had to take the hinges off the body of my jeep and use a hammer to get the hinges off the door. then used grease when i put them back on. Heard of some guys using a jack and a piece of wood and pressing on the bottom of the door to get it of. I highly suggest you dont do that. Thats why i took the hinges off the body. Just a little paint after hammering them off and it was fine.
04-07-2012 04:11 PM
KBR97 Yea just be careful of dropping the door when it pops, lol



Quote:
Originally Posted by Gunt View Post
I'm sort of having the same problem, but i'm not sure if the nuts have been removed. i didn't take them off but it doesn't look like there's a standard nut under there. I have a 99 tj and so if anyone has pictures of the nuts on/off it would help.

Thanks
Just look at the bottom of the door hinge, if there is a painted nut then they are still there.
If there is a little threaded stud sticking out about 1/2" from the bottom of the hinge then they are removed.
04-07-2012 03:58 PM
IJump
Quote:
Originally Posted by KBR97
I used a combination of PB blaster, a floorjack, a wood 4x4, and a rolled up towel.
That sounds like what we did for both our TJ and our JK. Then we dropped one of the JK doors when it popped off. The CJ doors came right off....
04-07-2012 03:45 PM
lembecricas Thanks guys helped abunch me n a buddy had to twist n pull them up but finaly go them off
04-07-2012 02:49 PM
1quick1 Yea soak in wd-40 and use a floor jack and wood block.
04-07-2012 02:49 PM
Gunt I'm sort of having the same problem, but i'm not sure if the nuts have been removed. i didn't take them off but it doesn't look like there's a standard nut under there. I have a 99 tj and so if anyone has pictures of the nuts on/off it would help.

Thanks
04-07-2012 02:44 PM
KBR97 I used a combination of PB blaster, a floorjack, a wood 4x4, and a rolled up towel.
04-07-2012 02:29 PM
wmwhitey Lift with your knees not your back.
04-07-2012 02:26 PM
Lbailey21 This maybe true, but it worked for me haha.
04-07-2012 02:26 PM
TJDave See how that works? We both posted at 2:22pm.

Age before beauty I guess!
04-07-2012 02:22 PM
TJDave
Quote:
Originally Posted by Lbailey21 View Post
Mine were super hard to get off at first too. I just grabbed my best friend WD 40 and they came right of. twist your door back and forth while lifting.
Yep, if they have never been off, or have not been off in a long time, they can be a PITA.

WD40, PB Blaster, or some penetrating oil on the top of the hinge. Wait a while for it to work it's way in there. Open and close door while lifting....two people might help this first time.

When you put them back on, make sure you apply some grease on the hinge rod before you put them in. My full doors slide right off every spring.
04-07-2012 02:22 PM
Jerry Bransford Soak the hinges with a good penetrating lubricant like Liquid Wrench, Break-Free, PB-Blaster, or Kroils. Then start swinging the door back & forth to work it in and then start lifting the door up as you continue swinging it. It will eventually come free. Lubricate the hinge pins with white lithium grease once the doors are off and this won't happen again.

By the way, WD-40 might work for this but I never recommend WD-40 for anything that needs a true lubricant. WD-40 is not a good lubricant no matter what WD-40's marketing department wants us to believe. Technically, WD-40 is a solvent that was designed for moisture displacement.
04-07-2012 02:17 PM
Lbailey21 Mine were super hard to get off at first too. I just grabbed my best friend WD 40 and they came right of. twist your door back and forth while lifting.
04-07-2012 02:13 PM
lembecricas
cant seem to get my doors off

Hey guys I have a 01 tj I bought at the end of last summer I never got to take the doors off so tdy I went to remove them and they won't come off...I took off the nuts on the bottom of the hindge already...am I missing something??!! Would apreciate any help thanks Rick

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:27 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC