|04-09-2012 09:48 PM|
|04-09-2012 09:21 PM|
WELL...i had a fun day.. I managed to get 1 bolt out, but of course the screw extractor broke off inside one, and a bit broke off inside the other....
|04-09-2012 05:31 AM|
|denisbaldwin||If the screw extractor doesn't work, heat and apply krill oil liberally until you can bust it loose. I'm also replacing all of mine with grade 8 hex head hardware. No reason to step back into a torx head nightmare if you don't have to.|
|04-09-2012 04:31 AM|
|mckey73||I plan on replacing them with hex head cap bolts. Harley uses the same crap.|
|04-09-2012 02:28 AM|
|H8-roads||Try pounding or cutting a slot for a flat screwdriver. The you can just reuse it too. Or if you have the ability get an air hammer (it always does the trick).|
|04-09-2012 01:06 AM|
|CottageGrove4x4||Well I might make a trip to the store tomorrow and see what i can get for drill bits. Ill take a shot at it...I know something is going to get f'ed up...|
|04-08-2012 09:10 AM|
|1jeeplvr||These are the worse bolts ever.Mayby it has something to do with the fact the vehicle gets painted AFTER the hinges are on.I know this because I had to adj my door hinge & there is now primer showing where I moved the hinge.|
|04-08-2012 08:26 AM|
LH drill bit should do it, with the added bonus that whatever heat builds up from the drilling might help break the thing loose. And then it will just unscrew.
Don't forget to soak it with snake-oil for a few days.
Screw extractors: Don't go cheap-and-cheesy. Buy the best ones you can find. Cheap ones tend to be overhardened, and if they break off in the screw, you REALLY have a hard time drilling them out.
|04-07-2012 11:47 PM|
|50Johnbob||Has anyone ever tried drilling them out with left handed drill bits?|
|04-07-2012 09:54 PM|
Always looking out for your fellow jeepers, I see!
|04-07-2012 08:34 PM|
If ya have a stripped out head you can usually turn the bolt by using a sharp "Prick Punch" (Don't laugh.... Thats what they are called ) Or a "center punch"..Very carefully drive the outside of the bolt head with the punch and a hammer. YESSSSS, Wear your Safety goggles.
I guess it would be good idea to pull these bolts once in a while and grease em or put on some Anti Seize.... Add that to your "PM" list.. "BH"
|04-07-2012 05:06 PM|
|greenenvey||put a vice grip on it to break it loose|
|04-07-2012 05:02 PM|
|Hammerdown||Screw extractors work so great on late night TV commercials.|
|04-07-2012 03:54 PM|
You can't leave that hanging like that Cubby.
I fixed your reply.
|04-07-2012 03:42 PM|
2. Don't let the description of how to do it fool you
|04-07-2012 07:42 AM|
|00tj2||Had it happen yesterday on my tailgate.. I drilled them till the heads poped off, I think it was a 3/8th bit. The with a vise grip I tightened as hard as I could I very gently was able to move the leftover stud back and forth till it came free... Those damn torx heads suck.|
|04-07-2012 12:42 AM|
Yeah, it sounds so easy. In my experience, it !#*%&@ sucks.
I posted awhile back in the YJ section about how I traded my soft top for a hard top and doors for free. I thought I was getting the bargain of the century. If I had it to do over again I would have skipped right by that damn Craigslist ad.
All three of the upper hinge bolts from the drivers door stripped out on me. I tried to use extractors and broke two of them off in two separate bolts. So I had my daughters husband over helping with the damn jeep and found out he knows how to weld. So I went and rented a tow behind welding kit so that we could weld a nut onto the torx bolts and remove them that way.
He couldn't get the weld to stick. The nuts would melt down but whenever we tried to turn them they would just pop off.
So I had to go buy another pair of doors from FN Jeeps. $400 dollars later I ended up with a pair of doors that are in worse condition than the ones I traded for but at least the damned torx bolts weren't jammed and I was able to mount them into place.
Oh, and this all happened on the last two days of my vacation.
|04-06-2012 10:35 PM|
1. That was the fastest response ever..
2. That sounds soooo easy..
3. I <3 you....
|04-06-2012 09:18 PM|
|backwards||And there you have it|
|04-06-2012 09:16 PM|
Just did this about two days ago.
|04-06-2012 09:08 PM|
stripped torx screws on door hinges..
Im replacing my door hinges because theyre rusted, and the torx screws are stripped.. i tried using a larger torx and applied pressure, but still no luck... i'm out of ideas.. help?