Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > clutch problem on 89 YJ 2.5

Join Wrangler Forum Today


Thread: clutch problem on 89 YJ 2.5 Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-12-2012 12:47 PM
Xpress Sure sounds like it might be the slave cyl... Is the fluid level dropping in the MC?

FWIW if you can get into 1st gear, then you don't need the clutch. It's all about rev matching
04-12-2012 11:33 AM
alpo96792 it wouldnt hurt. is there brake fluid leaking from the bell housing?
04-12-2012 11:22 AM
drpblair is it worth another bleed before attacking the slave?
04-11-2012 09:39 PM
alpo96792 x2 on the slave cylinder. too bad its internal hate the guy that designed it. good luck changing it. not too bad, just takes time
04-10-2012 10:46 AM
Timberwolf slave cylinder
04-10-2012 10:14 AM
drpblair
reply

in reply to previous questions:
1. no evidence of fluid leaking (although the reason I replaced the master cylinder was that there seemed to be fluid leaking inside the car where the clutch pedal linkage entered the cylinder) - I have replaced it with a metal cylinder not the plastic type.
2. I can start the jeep in first and drive off. By double declutching and getting the revs right I can change up through the gears and back down again - but this procedure could not be described as smooth - although it sounds and feels clunky rather than crunchy or grinding. I can brake to a halt in second gear and hold it on the clutch without stalling.

also pumping the clutch does not seem to change anything at all.
04-09-2012 01:19 AM
alpo96792 how is the hydraulic fluid? is any leaking?
04-08-2012 11:21 AM
cmoconnell if you time it right, can you float the transmission into any gears while rolling?
04-08-2012 11:04 AM
drpblair
clutch problem on 89 YJ 2.5

Problem is can not change into gear when engine running. Smooth gear change when not running. Can start in reverse or first with clutch depressed and move off smoothly on releasing clutch, can double declutch into second and third with a bit of crunching. Have replaced master cylinder and bled thoroughly with no change in symptoms.
Note that this first happened when i tried to reverse out of a parking spot in deep snow without clearing it first - in 4WD (posilok fitted) - I think I remember a bit of a clunking noise and I stalled. On restarting it would not go into gear.
If I engage 4 wheel drive the symptoms appear a bit worse as I can not get out of first gear even with double declutching.
Are there any simple tests that can be done to narrow down the problem.
If I have to remove the transmission what all should I plan to replace when I am in there.
Thanks for any insights.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:40 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC