|11-19-2014 03:22 AM|
|91AzXJ||This is my first post but I've been lurking around and read this entire thread over. I'm getting ready to put on a new set of 18/60 off a 2014 JKUR on my 04 TJ and am hoping for 2-2.5". Currently stock with 1" body lift. Will let you know how it turns out. I have a set of JKUR shocks on my 00 XJ with a 3.5" lift and they work great. Will see how the same type of shocks will work on the TJ with the rubi springs.|
|10-11-2014 05:02 PM|
|Horn5413||Doing this as we speak to my wifes 01 SE. The reason I am doing it is for the ride not the lift. I'm taking out the BDS 2.5 and Zone Nitro's because the ride was terrible and she hated it, I did also. Put 17's in the front, and the jeep is about 1.5" higher than stock. I have 55's and 58's to try for the rear. We will see tomorrow when I finish it if I can get it level with just the springs, or I do have spacers. We will see.|
|10-10-2014 03:07 PM|
Just swapped out my stock TJ shocks/springs with the JK shocks/springs. 17s in the front and 60s in the back. Ended up lifting the front about an inch (4.0 engine, heavy bumper, winch/10,000 pound winch) and lifted the back about 2 inches. Installation was relatively simple. Leveling it out soon. Slight vibrations so I'm going to drop the transfer case an inch or two and that should fix it.
I drilled out the bushings on the JK front stocks and swapped in the stock bushings and bar pin. As previously stated. No modification on the springs. On the back the shocks went right in and I cut about an inch off the top of the back springs to make them fit over the BS cup.
Over all ride quality is night and day better. Amazed how such a cheap and simple swap improved it that much. Highly recommended mod for a cheap lift and better ride. Thanks for the tips!
|10-05-2014 09:00 PM|
|RubiRoad||Jeepsr4me- Did you end up swapping the JK sway bars to the TJ as well?|
|09-24-2014 01:27 PM|
|jcjeeper87||Anyone know if the trackbar should be moved?|
|09-23-2014 01:37 PM|
|Oregon jeep||Going to install it this weekend I'll post picks just going to use springs and shocks|
|09-22-2014 06:18 PM|
|09-22-2014 09:44 AM|
|Stewarts06tj||So how did the control arms work?|
|09-21-2014 01:37 AM|
|Oregon jeep||Going to give this a try picked up springs shocks upper and lower control arms from a jk rubicon to put on my 04 tj for $100 on Craig's list|
|08-27-2014 08:35 PM|
|jdecker88||Now this is interesting. So a jku mod can be cheaper then the zone or bds lift just have to replace the spacers. But it must be jku springs correct and not just regular 2 Dr jk springs? I like the idea of using oem since the springs would hold up better then cheaper lifts|
|06-22-2014 03:27 PM|
|06-22-2014 03:14 PM|
|06-22-2014 11:33 AM|
|06-22-2014 11:30 AM|
|06-22-2014 09:44 AM|
|Suprarob||Why don't more people know about and use this mod?|
|04-03-2014 01:06 AM|
|Stewarts06tj||No, pitman is fine. Careful though the only problem I had with the whole thing was the front rake|
|04-03-2014 12:05 AM|
|ldluckman||Did you have to change pitman arms or anything else? I recently bought an 04 TJX and a set of JKU springs and as soon as I can buy some shocks I will put them on.|
|04-03-2014 12:02 AM|
|ldluckman||just scored a set of JKU springs for my 04 TJX did you have to change to a longer pitman arm or use stock?|
|03-26-2014 11:51 PM|
I have several boxes from qtec on the way I'm keeping the jkr shocks. But I'm not a fan of spacers, so I decided on ome f/r springs jks discos front and adj in rear, extended brake lines and bump stops.
The whole thing was really just an experiment. I hope after I get this all together I will have a capable 4x that I can dd without dropping thousands on complete LA's. Or huge tires
|02-24-2014 02:46 PM|
|02-24-2014 10:53 AM|
|brad98tj||Would 14s and 57s make a difference on my stock tj. I can get some I just want to know if it will lift it at all.|
|02-18-2014 08:27 PM|
I just bought today 18/59 springs, and a 2" leveling kit. Just looking for shocks now
Thanks everyone for all the great advise and input
|02-18-2014 07:38 PM|
|Stewarts06tj||Also as a warning. The shocks are longer. after testing I found that the bump stops need to be extended at least 1.5 and if you want any travel at all you must use the springs, a bb, or aftermarket lift springs. I'd say up to 3.5 would work.|
|02-18-2014 07:34 PM|
|Stewarts06tj||Yes Brit, jk springs fronts are direct with little to no lift but ride great, rears require cutting off 1.5 on top to fit but will take you up 2 to 2.5 depending on the number springs you get. Gotta do your research, here and jeepforum have several threads. My suggestion is to use the jk shocks, prefer Rubi. With 2.5 after market springs like ome or rancho. Your pref. cheep lift rides great! .|
|02-18-2014 07:26 PM|
|Stewarts06tj||Finished last night, details in my previous posts. Bar pins were by far hardest part. Heat them up and push them out! 2.5 rear 1.5 front with spacer! Wtf! Not what I expected. I like the stance though looks good with my 245 75 mtr's too. Rides amazing with no driveline vibe or alignment issues. Will update as they settle and I'll add pictures tonight.|
|02-18-2014 01:03 PM|
Just to throw something else out there.
Do you think aftermarket JK springs would work also ?
|02-18-2014 09:10 AM|
|1Felix1||Well I have more info. I have 2 1/2" of lift over the stock configuration. I measured a friends stock 2002 TJ last night. He has 31" tires just like I do. So I think I'm pretty sure of my measurement. I should have my ATB's by the end of the week. I will update.|
|02-17-2014 09:26 PM|
|brandon-99tj||Rubis came from the factory the height as all other TJs, they just had 31" tires. So without knowing more about the other rig, we cant tell you how much lift you got.|
|02-17-2014 08:20 PM|
Same setup as me but I have a 2000. I installed the springs and shocks this past weekend. All went well, lots of rusted bolts. For some strange reason I forgot to measure before I started the swap. So I'm not sure how much of a lift i have. But I definately need adjustable track bars.....and an allignment. I lowered the trans skid pan a lil over an inch to get rid of vibes (just temporary until I get a MML). This afternoon while getting gas a TJ Rubi pulls into the station. So I pull up next to him to see how my lift measures up. Come to find out he has a 2006 Rubi. We are the exact same heigth. I am sure someone with more experience that I can tell just how much of a lift I have....... face in palm........
|02-15-2014 08:20 PM|
I just finished installing the JK front & rear springs and shocks in my son's 1999 TJ. I gained 3" front and rear. It rides better. It's firm and doesn't sway as much in turns or rapid lane changes. Total out of pocket for today's 3" lift kit is $90. (note: I sourced used parts from a local 4X4 shop that I work for)
-To make it fit I used TJ BPEs on the front lower mounts, ground the metal sleeves with the bench grinder.
-The front springs fell into place. I got 1" of spring lift and added 2" TeraFlex spacers. I used Daystar extended bumpstops in the front.
-I cut the rear spring, upper coil 1.5" from the end. This allowed it to fit around the upper bumpstop. I then used spacers to lower the rear bumpstop down 1.5 inches. The springs are variable rate and provided 3" of lift.
-Used a set of 2-6" quick discount swaybar endlinks.
I will be going with adjustable trackbars to recenter the axles under the Jp. I will be saving for JKS up/low, Fr/Rr control arms.
|This thread has more than 30 replies. Click here to review the whole thread.|