Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > General Jeep Discussion > Clutch Exposed to Water?

Join Wrangler Forum Today


Thread: Clutch Exposed to Water? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-10-2008 08:00 AM
soupy1957 MOz: right on......when I go through a mud/water hole, I keep it moving .....great advice.

One comment: I've noted that SOME individuals think it necessary to blast through a mud/water hole at extreme speeds. There really is no need of this, right?

I always found that "steady" moderate speed was more than enough to get me through, unless I was going to attempt a "float" across a mud/water hazard, in which case, I probably WOULDN'T do it.

-Soupy1957
05-09-2008 11:48 AM
MOz There's a lot of guys on here with manual transmissions that fjord water crossings and mud bogs and have no isses.

I had an '65 CJ with a manual trans and I never had issues in deep water or mud. I used to beat the crap out of that thing on a regular basis and I never changed the clutch....

When you are in mud or water, keep it in a low gear and keep it moving... don't go any deeper than your intake and you should be fine.
05-08-2008 12:35 PM
distortedtj
Quote:
Originally Posted by Jaxs1stJeep View Post
Is there a reason for the 3/16" gap?

Why not just silicone it shut?
heat realease
05-08-2008 07:08 AM
Jaxs1stJeep Is there a reason for the 3/16" gap?

Why not just silicone it shut?
05-07-2008 05:57 PM
soupy1957 distortedtj: Yes it does....thanks!

-Soupy1957
05-07-2008 01:11 PM
distortedtj there are area's that water and mud can enter the tranny housing. it is not "sealed" to the motor only bolted.
The front bottom half of the tranny has a inspection plate "Dust cover" over it. This cover is also not sealed to the tranny housing only bolted. If you look at the bottom of the inspection plate you will see and opening about a 3/16 inch wid and about 10 inches long at the front bottom of the tranny housing. This is where water/mud/debrie may inter the tranny.

As for "bad" to clutch while in water/mud. yes it is not suggested.
With the water or mud in the tranny....when you clutch (press clutch pedal to the floorboard) the pressure plate releases presure from the clutch disc and the fly wheel.
"opening them up/seperates them"
This can allow water/mud to get inbetween the plate/disc/flywheel.

To sum what will probally happen if you get fluid or mud/debre in there.....you will be replacing them. Fluid on those parts is not good!


hope that helps?
05-07-2008 06:32 AM
soupy1957
Clutch Exposed to Water?

I've had a good amount of mechanical experience over the years, but not a whole heck of a lot with Clutch plates.
I changed a clutch plate on a Honda Prelude once, but I have little or no experience with the location or replacement or design of a clutch plate setup in a Jeep....thus THIS question:

A good and trusted friend of mine, while taking me down a trail not long ago, mentioned at one point that "clutching while in a water/mud hole is not a good thing because it exposes the clutch plate to the water and mud."

I accept that "water-n-mud" can be a bad thing on internal engine and drive train components, which seems fairly obvious, but I always thought that the clutch plate was enclosed in a housing that was not able to be penetrated by outside influences like water-n-mud.

Could someone educate me a bit about the design of the clutch plate in a Jeep motor, with regard to exposure?

-Soupy1957

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:51 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC