Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > sye install

Join Wrangler Forum Today


Thread: sye install Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-23-2012 05:34 AM
timberland In my Dad's 2006 TJ he had both the circle ring and snap ring....these shown are the actual ones I removed. If you look in you tube and search for "Advance Adapters how to Jeep SYE install" its shown there.
04-22-2012 11:03 PM
DevilDogDoc
Quote:
Originally Posted by timberland View Post
In addition to a really good pair of snap ring pliers....get a pair of circle ring pliers too. You'll have exactly these clips to contend with. The circle ring will be a bear to remove / install with out these pliers. I did my Dad's STE two weeks ago. It was a whole lot easier doing the SYE than my 4" spring lift the weekend before. He had a RC 4" lift on his 06' TJ and it vibrated. I installed a Zone 4" on our 06' TJ and it doesn't vibrate....therefore I wont be doing a SYE on our TJ. I believe I bought my circle ring pliers at Sears - Craftsman 25 -30 yrs ago....the snap ring pliers are Snap -On brand. Each of those rings are about 1 1/2" diameter.
Yep top pic is what you want, lock ring pliers, all over Ebay, Sears etc....
Snap ring pliers might work but I broke the tips off of a couple of pairs of mine so I would rather use the right tool than ruin the wrong one.
04-22-2012 10:45 PM
TnDz TJ
Quote:
Originally Posted by timberland View Post
In addition to a really good pair of snap ring pliers....get a pair of circle ring pliers too. You'll have exactly these clips to contend with. The circle ring will be a bear to remove / install with out these pliers. I did my Dad's STE two weeks ago. It was a whole lot easier doing the SYE than my 4" spring lift the weekend before. He had a RC 4" lift on his 06' TJ and it vibrated. I installed a Zone 4" on our 06' TJ and it doesn't vibrate....therefore I wont be doing a SYE on our TJ. I believe I bought my circle ring pliers at Sears - Craftsman 25 -30 yrs ago....the snap ring pliers are Snap -On brand. Each of those rings are about 1 1/2" diameter.
The top pair of lockring pliers is all I used on my SYE install.... there were no snaprings in my 231 to mess with when I did my SYE and Jerry is right... you need them to open about 1" or a little bigger...
04-22-2012 08:11 PM
timberland In addition to a really good pair of snap ring pliers....get a pair of circle ring pliers too. You'll have exactly these clips to contend with. The circle ring will be a bear to remove / install with out these pliers. I did my Dad's STE two weeks ago. It was a whole lot easier doing the SYE than my 4" spring lift the weekend before. He had a RC 4" lift on his 06' TJ and it vibrated. I installed a Zone 4" on our 06' TJ and it doesn't vibrate....therefore I wont be doing a SYE on our TJ. I believe I bought my circle ring pliers at Sears - Craftsman 25 -30 yrs ago....the snap ring pliers are Snap -On brand. Each of those rings are about 1 1/2" diameter.
04-22-2012 07:07 PM
Jerry Bransford Actually, I should have said snap-ring pliers for a SYE installation. So long as they open to 1" at the tips you should be fine.

These are what I use...
04-22-2012 06:50 PM
jrmiller Ok. Also as you can obviously tell I'm no tool expert but are snap ring and lock ring pliers different
04-22-2012 06:46 PM
Jerry Bransford Mine open a full inch at the pins that go into the lock ring's holes which is wide enough for a SYE installation. That doesn't sound like much but not all can spread open a lock ring that much.
04-22-2012 06:35 PM
jrmiller Ok. How will I know if they open wide enough?
04-22-2012 06:22 PM
Jerry Bransford What you want are lock ring pliers that open widely enough, not all do. I had two very good quality sets in my tool drawer and neither opened widely enough. I finally found a set that opened widely enough on a Matco Tool truck parked at a car dealership. Snap-On trucks have them too. I've been told Sears now carries lock ring pliers that open widely enough but they didn't when I installed my SYE 12-13 years ago. NAPA didn't have them either.
04-22-2012 06:17 PM
crkid Can't go wrong with Craftsman.
04-22-2012 05:55 PM
jrmiller
sye install

Have a couple week break in wheeling trips so I'm hoping to get my sye done. I have everything ready to go except snap ring pliers. Everyone always mentions that a nice set is needed..just wondering what is a "nice set" and where to get them. Places local to me are the typical Sears, Lowes, all the auto stores and of course anything online. Not looking for anything crazy expensive as this will be the only use they see more than likely

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:49 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC