Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > blind squirrel found a nut

Join Wrangler Forum Today


Thread: blind squirrel found a nut Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-25-2012 07:11 AM
arcountryboy Send it to these guys and they will rebuild it. Long block ( complete engine minus covers and accessories) is what you would want. They have my short block there right now. I have dealt with this place multiple times and never had an issue. They have been in business since 43, a BBB member since 57 and a A+ rating.

Remanufactured Engines by City Motor Supply - Domestic and Import

The very 1st engine is what you need, as of last week, they did not have one in stock, but would rebuild yours with a 2 week turnaround. If they rebuild yours, there is no core charge.

http://citymotorsupply.com/domestic.pdf

By the time you factor in parts, cleaning stuff, and machine work, you'll be hard pressed to build one yourself for this price. I have built many engines, but by the time it is all said and done, I would save about 50 bucks doing it myself. My time is worth more than 50 bucks.
04-24-2012 08:59 PM
Buz 1 pull the plugs & pour 2-3 tbs of marvel mystery oil into each cylinder & let soak 3-7 days.. new t-chain & sprockets(as mentioned), & re-torque head (as mentioned).. install, & enjoy...
04-24-2012 08:04 PM
wiseguy52 The gas in my Jeep is new, the 3 year old gas is in the rotted jeep that I am purchasing the engine from. I am considering the rebuild while the engine is not in a vehicle.
04-24-2012 05:58 PM
Shoe If the gas is 3 years old, I would drop the tank and drain all of it out. Old gas can do bad things to an engine.
04-24-2012 05:25 PM
530ktm Why not just get the one in the Jeep rebuilt?
04-24-2012 03:29 PM
2002TJ Yup, paint it Chevy Small Block Orange for 25 free HP. Promise

Pull the pan and valve cover, clean them out and look close at all you can see. Check crank thrust. Replace oil pump and clean pickup tube screen. Replace cam drive sprockets and chain. Replace freeze plugs. Flush cooling system like crazy. Replace rear main seal. Consider pulling a main cap and rod cap to check bearing condition.
Check torque on head bolts and all rods and main cap bolts-don't do breakaway, just check up to torque spec. Replace water pump and tstat.....stuff it in
04-24-2012 03:12 PM
wiseguy52
blind squirrel found a nut

So I have been looking into replacing the 2.5 in my 98TJ for some time now. I was contemplating upgrading to at least the I6 if not a V8, but was concerned about all the extra work and cost involved.
I happened to find, and purchase a 2.5L for a very fair price recently The engine has around 80K miles on it and has been sitting for a few years. As of yesterday, the engine ran. I was told it was running rough, but considering it had not run since parked about 3 years ago, I am not all that concerned. I should mention it still has the gas in it from 3 years ago as well.
I plan to look at the seals, replace plugs, probably put gas treatment in the tank before starting, and anything else obvious before putting it in my jeep. Is there anything else that you would do prior to putting the engine in the jeep? Thought about rebuilding it, but I am unsure of that.

All feedback is appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:39 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC