Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Mud Behind the Tail Lights JK

Join Wrangler Forum Today

Thread: Mud Behind the Tail Lights JK Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-04-2013 09:09 AM
SilverSport Should be fine.
06-04-2013 08:59 AM
DirtyTeddy Old thread and maybe the OP won't chime in but would I be able to use something like

Not sure what the difference between this and marine foam is, they both seem to be made of polyurethane
05-12-2012 05:07 AM
strider_mt2k I noticed dried mud in that section when I was installing stuff too.

That is an interesting idea.
09-10-2011 04:50 PM
MrSig UP dated for 2011 & up
On the passenger side it is all sealed up no more foam pad. Under shot.

Inside shot.

Drill a 5/8" hole from the bottom up. I had to remove the tire to get in to the spot to drill.

Feed hose in and up with no cap on.

Loop the hose in side well and put cap on and secure up with wire tie.
Add foam.

Finish running hose to rear diff. Don't forget to check for clearance with axle and spring, wire ties in and your done.
09-05-2011 05:07 PM
Mud Behind the Tail Lights JK

I did this Mod on 10.15.07
A hole in the bottom of the jeep will shoot mud (where the piece of foam is)up and behind both of the rear tail lights.

First remove the tail lights The 2 screws only on the right side of the left light and the left side of the right light. Then clean out the cavity well! Remove the foam block from both holes.

Left side out.

Right side out.
Next you see the hole on each side.

Left side hole.

Right rear hole.
Then place a piece of rubber over the holes.

Next fill with Marine low expansion foam.

Left side full up to the tag wires and don't get any on the gas breather.

Right side about half way up.

Let cure, reconnect wires to lights and screw back in..

Left rear done!

Right rear done!
Now no more mud or stuff will go up into the holes and rot out behind your tail lights..
I got the marine low expansion foam from a boat repair house. It is made to breath and will not let water stay in but keep dirt out!
Follow Up!
On the 23rd at 7am I removed the right tail light and put in 28oz of water on top of the foam then put the tail light back in.
Just a little bit ago (3pm/1500hrs) I removed the right tail light and checked the cavity and not a drop of moister was found! So this was a great fix it keeps the dirt, & mud out but still lets it breath!
As of today still works great!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 06:42 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC