|06-19-2008 03:46 PM|
|branty||Nope, doesn't matter which end you start with. But like you said, start with one end and work until it's done, then move to the other. You'll do fine. Def take some pics to document the install. Good luck.|
|06-17-2008 07:36 PM|
Naw, just the front. The rear has a track bar relocator bracket.
The included directions have me doing the front first, then the rear, then adjusting the front track bar. I'd rather pick an end and stick with it til it's done. Maybe I'll start with the rear and work my way up to the front. I guess it really doesn't matter.
I'm really looking forward to it. It'll be my first Jeep lift. It looks to be about as simple as they come. It's not as if I'm stretching and long-arming the thing, so I don't see things going too bad. I'll try to take some pics in progress and some after pics.
Thanks for the encouragement!
|06-17-2008 06:04 PM|
|1BLKJP||I would assume you have adjustable trac bars at both ends. So honestly it wouldn't matter which one you do first. Just take your time and have fun.|
|06-17-2008 04:29 PM|
|06-17-2008 03:03 PM|
|branty||If that's all it says then I would probably set it with about 2 or 3 threads showing. Question: Are you doing the front or rear first?|
|06-17-2008 02:57 PM|
|06-17-2008 02:49 PM|
Anyone feel free to jump in and correct me if I am wrong but based on my experience the instructions should have measurements for each component. You will go ahead and adjust the track bar to the recommended length before installing. Once adjusted, go ahead and install it with everything apart. This will make it easier to install. You will want all the bolts on your control arms to be loose so that you can shift your axle from side to side in relationship to the frame. Once all installed, if the measurements were correct for your Jeep, it will be centered. After you pull it off the lift and measure from the frame to the outside wall of each tire, you will be able to tell if its centered. If not, you will have shorten it or lengthen it depending on how its off center. These adjustments are done much easier (in my opinon) when everything is apart.
If you do it sitting on the ground with the tires on, be prepared to have a ratcheting tow strap handy. The frame will most likely need to be pulled to one side or the other of the axle to get the track bar installed at the correct length. Hope this helps.
|06-17-2008 12:59 PM|
|tiny terror||Don't you dare get blown up again.|
|06-17-2008 12:51 PM|
|06-17-2008 12:33 PM|
|tiny terror||Ewwwww cool. I expected the outline of a bolt head on your ankle though.|
|06-17-2008 12:21 PM|
Also, when adjusting the track bar (it's adjustable), can I do that after the tires are mounted and the Jeep is sitting on the ground? I don't have to do that when the Jeep is still sitting on the hydro lift do I? The directions are pretty good, but that part was a little ambiguous. Thanks for the help so far!!
|06-17-2008 10:37 AM|
Still haven't gotten any x-ray pics. Here are a few of the leg. Pretty gross, I know.......
You should have seen it the day they did surgery. It was every color of the rainbow and swollen up bigger than Oprah's ever were.
|06-17-2008 10:25 AM|
Jeeze Cavy, it hasn't been that long. Be careful.
(and just where are the pictures of the lag bolts and wing nuts holding your foot on??? )
|06-17-2008 09:58 AM|
Try this link:
It is a 6" install but I imagine many of the details will be similar. Hope this helps.
|06-17-2008 09:11 AM|
i fought my xj front springs for a while, cuz i didn't want to walk over to my box and get my spring compressor out. that was dumb. us a spring compressor to crush the springs down a little to get them in, thats my advice. then the axle doesn't have to get moved all over as much.
good luck, glad to hear you're healing up.
|06-17-2008 09:05 AM|
Getting ready to install my lift....finally!
Well, the time has come that I feel comfortable enough with my leg injury to do the suspension install on my Jeep. I've been waiting until my leg heals to the point where I can walk on it without the use of crutches and that time is at hand!! FINALLY!!
So I'm here to ask if there's anything I should know beforehand about installing the 3" FT lift. I'm pretty mechanically adept, so I doubt it'll give me too many problems. Just wanting to know if anyone else has experience installing this lift and has some tips and advice for me. I'm using a vehicle lift so it should be an easy task. I have full access to an Auto Craft Shop here on base. It's got all the tools I think I'll need. Let me know if anyone thinks of some good advice to send my way.