Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Communications and Electronics > HAM radio in jeep

Join Wrangler Forum Today


Thread: HAM radio in jeep Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-20-2012 09:36 PM
robtwitte I describe my radio install on my blog: Jeep Wrangler Radio Install | KØNR: Radio Enthusiast

73, Bob K0NR
05-20-2012 06:59 PM
ThingsAbove Documented my ham radio install in this thread...

http://www.wranglerforum.com/f40/ham...ed-148890.html
05-20-2012 06:37 PM
BlueRidgeYJ May not be the prettiest, but I sure do like it.

What I used:
2 pieces angle iron, ~12"
3 radiator band clamps, ~76mm(3")
1 piece 1x1/8x~18" aluminum bar stock
2 small washers
1 bolt/washer, ~5/16 thread and tap to match
3 bolt/washer/lock nuts, ~5/16 thread
1 bolt/2 washers/lock nut/nylon washer, ~1/4 thread x ~1"Length
~ 20' submersible pump power cable (12ga braided water shielded 3 strand)

Found/scrounged some, bought the rest, about 50$ in so far.

Tools:
tap from above
Drill / bit index
ability to bend metal
wrench/sockets/fastener head tools (torx, allen, etx)

Used the radiator band clamps to attach the 1st piece of angle iron to the "roll" bar in the upper left corner, at the A pillar. Took the second piece of angle and bent it to the angle of the windshield to maintain a level plane, ~80% or so. Removed the sun visor, and using the 2 small washers, attached the angle iron to the windshield frame with the visor bolts / holes. Bolted the two angle irons together in the corner (1 of 3 bolt/washer/lock nut). Tapped a hole towards the right of the 2nd angle iron and put a bolt in it, more for stability than support (going into the windshield frame, similar to the sun visor holes). Attached alum bar from angle 1 to angle 2 (bolt/wash/lock nut 2 & 3), mounted radio bracket to center of bar (1/4x1 bolt/lock nut) with nylon washers in between (so it can swivel). Used alum scrap to make a mic holder with the 2nd sun visor bolt hole set, ran sub pump wire to battery (with fused link) and attached it to the quick connect behind the radio, so I can take it out. As this is a FT 2900, I was able to also cable lock the radio to the angle iron as a theft deterrent/keep a radio from slamming into my face device.

It was too sunny to snap a good pic, sorry.
05-16-2012 03:32 PM
Sccafire
Quote:
Originally Posted by pfig88 View Post
That's a nice clean set up with only the head unit in view - do you ever have problems with water or things bashing into the unit since its open in the tub?
I have no issues with it at all. I was going to mount it under the seat at first. I decided not to because of water. You cannot tell from the picture but that is a little recessed area. The ice chest slides in right next to it and helps protect it. When I do pack up the jeep, I slide the ice chest in and do not pack anything else around it to keep air flowing around it for heat disipation.

I can get a picture of what I am talking about if it would help you visualize it.
05-16-2012 03:01 PM
pfig88
Quote:
Originally Posted by Sccafire
Here is mine. 05 TJ. Yeasu FT-8800R
That's a nice clean set up with only the head unit in view - do you ever have problems with water or things bashing into the unit since its open in the tub?
05-15-2012 04:10 PM
Sccafire Here is mine. 05 TJ. Yeasu FT-8800R



05-14-2012 10:52 PM
mzbrandi Nice idea. Would like to see antenna placement on the new JKs.
05-14-2012 07:23 PM
pfig88
HAM radio in jeep

While considering radios for a jeep, it struck me that I could ask you guys- so lets see some pics of your HAM radio setups!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:29 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC