|06-03-2012 09:01 PM|
|06-03-2012 09:00 PM|
Today I ordered some more parts from Quadratec...$630.00 later but I am happy!
1 Quadratec Floor Liners (Front & Rear)
2 Clear Signal & Marker Light Lenses
3 Mopar Hood Vent Scoop
4 IPCW LED Tail Lights (Bermuda Black)
|06-01-2012 03:43 PM|
Today I got more stuff in, I can't wait to install it all but it is raining here now so I have to wait until the weather breaks...
New Bushwacker Fender Flares (Front & Rear)
New Rugged Ridge Mesh Grill Insert (Black with Polished Stainless Highlights) along with a Warn Winch Neoprene Cover...
...And New Kentrol Stailsess Steel Rear Tail Gate Hinges!
|06-01-2012 03:36 PM|
|05-29-2012 09:02 PM|
|05-29-2012 12:50 PM|
|05-29-2012 11:57 AM|
|05-29-2012 10:39 AM|
|Psychoink||Oh man looks like X-mas to me.|
|05-29-2012 09:52 AM|
|05-29-2012 04:04 AM|
|05-28-2012 09:52 PM|
|05-28-2012 08:23 PM|
|MacCTD||Just curious, I see you have a Warn winch and an air compressor, did you consider the Warn winch/compressor combo?|
|05-28-2012 07:45 PM|
If it sticks, lube it!
But yeah...listen to Jimbo. Don't lube your wheel studs.
Loctite blue green or red, regular grease, lithium grease, anti-seize, oil, dry-lube, paraffin wax, teflon tape, Grade 8 vs stainless, with lock washers, with concave washers, with a tension spring, with nylock insert, titanium bolt in a stainless helicoil in an aluminum heat sink, etc etc etc. What a topic this could become!
|05-28-2012 07:25 PM|
If you broke new bolts, because the nuts seized ---then they were either corroded, or you got the wrong nuts--
You should never put oil on bolts--then the torque values are "KAPUTT" or the Nylocks, don't Nylock-
In some cases you might wanna use some "BLUE" LOCTITE--nothing else !!
I sure hope you don't have any trouble with your wheel studs and lug nuts !!
|05-28-2012 07:00 PM|
|05-28-2012 06:53 PM|
|05-28-2012 06:46 PM|
That's a nice pile of stuff! I've got winch envy
Here's a piece of advice nobody asked for
Give the hood latch mounting bolts a couple drops of 3-in-1 oil or a squirt of WD-40 so something before threading on the nylock nuts.
I installed mine last month and the nuts seized half way down the bolt. I broke the bolts in half trying to back the nuts off.
Quadratec came through with excellent service and sent me a whole new package. I then oiled the threads and everything went well.
It might have been a fluke, but I'd hate for you to go through the same thing.
|05-28-2012 06:30 PM|
|05-28-2012 06:00 PM|
I am in Toronto too.
Share now! lol
|05-28-2012 03:36 PM|
|05-28-2012 03:35 PM|
|Sinz||Yes I will install it when I get the sliders & Bumpers powder coated!|
|05-28-2012 03:34 PM|
|ESP||Remember you're not supposed to bring things to WF if you don't share.|
|05-28-2012 03:33 PM|
|AdrianVall||Do you plan on installing any of it?!|
|05-28-2012 03:32 PM|
|Sinz||Still waiting on the JRC Bumpers, Tire Carrier, AEV Heat Reduction Hood, Drake Interior Accessories, Recovery Kit, Hi-Lift & some miscellaneous other parts lol!|
|05-28-2012 03:26 PM|
|ESP||Mmmm...parts. So what's next?|
|05-28-2012 03:24 PM|
|wmwhitey||So jealous rite now.|
|05-28-2012 03:19 PM|
Parts are starting to come in!
It's Christmas time for me again today some of my never ending list of parts came in...
Drake Hood Latches & Air Compressor...
Warn Winch CTI-S 9.5...
Parts accumulating in the spare bedroom along side my sliders and Hardtop