|04-10-2014 10:36 AM|
|Levi12||mine is in the shop right now. you have to replace the cluster at the dealership for the right mileage to be on the new cluster. expensive mistake.|
|03-27-2014 05:55 AM|
|03-27-2014 05:26 AM|
|03-26-2014 12:28 AM|
|silver rubi||Replace the cluster|
|02-25-2014 06:07 AM|
|09-25-2012 12:54 AM|
|08-21-2012 09:44 AM|
|Levi12||I am having this issue right now, I have been pulling the fuse under the hood and haven't had any issues until now. I will try disconnecting the battery, keeping my fingers crosssed.|
|05-31-2012 10:36 AM|
|silver rubi||What does a "hard boot" consist of? I have run the diagnostic test and it doesn't bring up any error codes. Both fuses look good.|
|05-29-2012 09:52 PM|
|Neil F.||Replace fuse #4 with a switch. You can make one yourself for a few $ and parts on hand, ebay has them for 15 or Quadratec for around 25-30. I put the switch on the side of the dash. When you pull the doors, just flip the switch and the lights stay off.|
|05-29-2012 06:45 PM|
s14sh3r - I've run it multiple times. It cycles through everything and then that's it..
Neil- that's good to know. What kind of switch are you talking about?
|05-29-2012 06:33 PM|
|05-29-2012 05:58 PM|
|s14sh3r||Have you or the dealership ran a cluster diagnostic test? With the key off, press and hold the trip meter reset. While holding the reset button, turn the key on. Let go of the button and the cluster will cycle through all the gauges and lights, and display any fault codes.|
|05-29-2012 05:46 PM|
|silver rubi||Neil, You haven't had any issues with removing the fuse behind the glovebox?|
|05-29-2012 04:23 PM|
|05-29-2012 04:15 PM|
|silver rubi||Thanks Pete! I'll try that tonight.|
|05-29-2012 04:14 PM|
|05-29-2012 09:51 AM|
|05-29-2012 09:39 AM|
|05-29-2012 08:52 AM|
|TJ Hooligan||I had the doors off and the fuse out this weekend with no issues. I'm keeping an eye on this thread for future reference.|
|05-29-2012 07:56 AM|
#4 under the hood is the radiator fan I think. (Almost did the same thing my first time) You want the #4 fuse behind the glove box as stated above. You'll have to remove the retaining strap so be prepared to catch the glove box as it falls. I just use a mini fuse puller and keep the fuse and puller together in the jeep bag my owners manual came in. You're looking for a 10 amp mini red fuse. Once you pull it, there will be no more chime to remind you your headlights are on so always double check. (Learned that the hard way by trying to leave for work and having a dead battery lol)
As for the odo reading 8's across the board, I would disconnect the positive and negative terminals for a few minutes, say 5-10. (Now would be a good time to clean all your battery connections and clear any crap that may be on there too!) Check to make sure the fuse from under the hood is still good, if not replace as necessary. Reconnect the battery and by that time the computer should have ample time to reboot itself.
|05-29-2012 05:20 AM|
|Neil F.||For one, it is fuse #4 behind the glovebox to keep the interior lights off, not under the hood. Make sure the fuse under the hood is still good. Put another one in the spot under the hood and check the odometer.|
|05-29-2012 01:20 AM|
Anatak I am not sure if the dealership tried that or not. How long does it need to be disconnected? I can try it in the morning.
|05-29-2012 01:14 AM|
I know this is obvious and already been tried, but I still gotta ask.
Have you or the dealership disconnected the battery for any extended period of time to perform a "hard-boot" on the computer?
|05-29-2012 12:38 AM|
|wmwhitey||HMMMMM thats a good one I will be watching to see what the issue is.|
|05-29-2012 12:33 AM|
Help!!! Odometer issues
I have a 2006 Wrangler Rubicon. I took the doors off my jeep and removed the fuse (under the hood) to turn the interior lights off while the doors were off. When I put the fuse back in, the odometer read 888888. The computer in the Jeep is still reading the correct mileage. I have had the dealership look at it and they don't know what to do. I don't want to have to replace the entire cluster. Please help me!