Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Oil PSI Issues

Join Wrangler Forum Today

Thread: Oil PSI Issues Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-02-2012 12:59 AM
Jerry Bransford Newer TJ oil pressure gauges were reprogrammed so as long as the true oil pressure is okay, the pointer will stay at mid-scale no matter what. Too many newbies who don't know much about their engines were complaining their oil pressure was going up & down.
06-01-2012 11:30 PM
NewtQ2 Thanks for the info. I run factory MOPAR filters and Mobil 1 Synthetic. I don't have any ticking lifters. That tells me I have some oil pressure. I am installing a mecanical gauge this weekend, mainly for piece of mind.
05-30-2012 10:20 PM
Skydiver I have a mechanical guage threaded into a tee between the block and sending unit. When I start my jeep, there is a split second delay from when the engine first starts to the needle moving on the mechanical one. The dash guage always has had a delay, even if I shut it off and restart instantly, so the dash guage is not exactly speedy in transmitting information. Oil pressure delay to the mechanical guage seems a little worse when it is below freezing. I tried putting a Mobil1 filter on it and there was zero change. The whole issue is probably not ever going to be a problem, but since I have tried two different filters and they have both responed exactly the same as a PH16 Fram. I dont see the point in different filters. I have always run a conventional 10w-30.
However, Accusump is a manufacturer of oil accumulators which have more roots in racing, but I feel has excellent possibilities off road as well. I do not like hearing lifters tick on a freezing morning startup, even if it is only for half a second. A 12 volt dc solenoid valve rated for high temps and oil with a home made bottle of some sort mounted vertically would act as a decent accumulator, much the same way as water hammers function in a house. Just make sure the line feeding it is restricted in some way so the oil pump fills it back up slowly, ensuring oil to the engine first. That is my plan to build one sometime this summer before it gets cold again. If I procrastinate too long, I will probably just buy one.
05-30-2012 09:59 PM
NewtQ2 NO FRAM!!!! They would have to pay me, been there done that. I am running factory MOPAR.
05-30-2012 09:50 PM
Skyhawk32 Get a mechanical gauge on it quick and are you using fram oil filters? If so try changing to wix.
05-30-2012 09:44 PM
Oil PSI Issues

My 06 Rubicon has developed a "Lazy" oil psi gauge. On inital start up it seems to lag before coming up, then it goes just past half way and stays, no matter what the RPM is. I suspected the sensor/switch. replaced it with no change. I grounded the purple wire to the sensor expecting the gauge to max out, it didn't. I have not put a mechanical gauge on it yet.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 07:26 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC