|11-20-2014 05:40 PM|
Works on '08, '10, '12 and '15.
I'm starting to think I need a 12-step program, not a seat belt chime program.
|11-20-2014 02:11 PM|
Thanks for the useful tip!
First time it didn't take probably because unbuckled and rebuckled in the On position rather than starting it. Did it again only started it and seems to have worked.
|04-05-2014 09:57 AM|
|Czee76||Finally! Thanks for the post!|
|04-04-2014 03:25 PM|
|Tusinator||Works on a 2014 jk as well|
|07-01-2013 10:47 PM|
|ironman2443||Thanks for the info!!|
|06-30-2013 01:22 AM|
|ChipW||works on a 2013 model also, what a relief to get rid of the dinger on the trail.|
|06-30-2012 01:11 AM|
|06-30-2012 01:03 AM|
Just to add another update on how to do this. follow above insturctions. at the end, when you have the seat belt buckled, SHUT THE VEHICLE OFF.
I'm an idiot and spent an hour doing the above instructions then immediately firing up the vehicle to no avail. What finally fixed it? Above instructions and at the end turn the key back off! I felt like an idiot lol
Thank you so much guys!
I know there have been a lot of flame wars about this topic (i drive with it on).... but when I'm out feeding cattle on the farm using my jeep... the seat belt is a hassle, and the beeping about drove me dang insane!
|06-17-2012 07:40 AM|
|CA3||Yeah, my bad. You have to have your seatbelt buckled when you turn on the ignition and you have to wait for it to cycle through the warning lights before you start the unbuckle/buckle process.|
|06-16-2012 02:43 AM|
MISSING->and wait for the Seat Belt Reminder Light to turn off.
NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the
ON/RUN or START position. Chrysler Group LLC does
not recommend deactivating BeltAlert.
1. Turn the ignition switch to the OFF position, and
buckle the driver’s seat belt.
2. Turn the ignition switch to the ON/RUN position (do
not start the engine), and wait for the Seat Belt Reminder
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver’s seat belt at least three
times within 10 seconds, ending with the seat belt fastened.
The instructions above seem to be missing--> and wait for the Seat Belt Reminder Light to turn off.
Good Luck, at least you only need to do it once
|06-16-2012 02:06 AM|
|BlackOpsJeep||hmm...tried several times to no avail on my 12 JKU. I'm pretty tech savvy and I'm doing it exactly as instructed.|
|06-15-2012 09:27 AM|
|Ran-Bo||Thanks guys...worked like a charm.|
|06-14-2012 11:02 PM|
|06-14-2012 06:22 PM|
|CA3||Insert key into ignition, buckle seatbelt and turn key to on but do not start engine. Within 60 seconds, Unbuckle and buckle seatbelt 3 times, cycling seatbelt indicater on and off. Red LED in lower right of guage cluster will flash three times to indicate reprogram.|
|06-14-2012 04:42 PM|
Pretty sure it is in the manual (at least it was for my 2011)...
But Google does the trick, too
How do you disable seat belt alarm 2010 jeep wrangler
|06-14-2012 04:31 PM|
Programming Seat Belt Alarm
Hey all...does anyone know how to program the 2010 Wrangler to eliminate the annoying seatbelt dinger. My wife's 2008 Liberty was easy, it referenced it right in the manual...can't find anything for the Wrangler.