Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Programming Seat Belt Alarm

Join Wrangler Forum Today


Thread: Programming Seat Belt Alarm Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-05-2014 08:57 AM
Czee76 Finally! Thanks for the post!
04-04-2014 02:25 PM
Tusinator Works on a 2014 jk as well
07-01-2013 09:47 PM
ironman2443 Thanks for the info!!
06-30-2013 12:22 AM
ChipW works on a 2013 model also, what a relief to get rid of the dinger on the trail.
06-30-2012 12:11 AM
mo1416 Good info.
06-30-2012 12:03 AM
Prelud3 Just to add another update on how to do this. follow above insturctions. at the end, when you have the seat belt buckled, SHUT THE VEHICLE OFF.

I'm an idiot and spent an hour doing the above instructions then immediately firing up the vehicle to no avail. What finally fixed it? Above instructions and at the end turn the key back off! I felt like an idiot lol

Thank you so much guys!

I know there have been a lot of flame wars about this topic (i drive with it on).... but when I'm out feeding cattle on the farm using my jeep... the seat belt is a hassle, and the beeping about drove me dang insane!

Thanks!
06-17-2012 06:40 AM
CA3 Yeah, my bad. You have to have your seatbelt buckled when you turn on the ignition and you have to wait for it to cycle through the warning lights before you start the unbuckle/buckle process.
06-16-2012 01:43 AM
Rooster76
MISSING->and wait for the Seat Belt Reminder Light to turn off.

Quote:
Originally Posted by CA3 View Post
Insert key into ignition, buckle seatbelt and turn key to on but do not start engine. Within 60 seconds, Unbuckle and buckle seatbelt 3 times, cycling seatbelt indicater on and off. Red LED in lower right of guage cluster will flash three times to indicate reprogram.
Remove Seat Belt Reminder Chime -Enhanced Seat Belt Use Reminder System
(BeltAlert_)
NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the
ON/RUN or START position. Chrysler Group LLC does
not recommend deactivating BeltAlert.
1. Turn the ignition switch to the OFF position, and
buckle the driver’s seat belt.
2. Turn the ignition switch to the ON/RUN position (do
not start the engine), and wait for the Seat Belt Reminder
Light to turn off.

3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver’s seat belt at least three
times within 10 seconds, ending with the seat belt fastened.

Quote:
Originally Posted by BlackOpsJeep View Post
hmm...tried several times to no avail on my 12 JKU. I'm pretty tech savvy and I'm doing it exactly as instructed.
It worked for me on my 2012.

The instructions above seem to be missing--> and wait for the Seat Belt Reminder Light to turn off.

Good Luck, at least you only need to do it once
06-16-2012 01:06 AM
BlackOpsJeep hmm...tried several times to no avail on my 12 JKU. I'm pretty tech savvy and I'm doing it exactly as instructed.
06-15-2012 08:27 AM
Ran-Bo Thanks guys...worked like a charm.
06-14-2012 10:02 PM
Rooster76
Quote:
Originally Posted by Oglethorpe View Post
Pretty sure it is in the manual (at least it was for my 2011)...

But Google does the trick, too

How do you disable seat belt alarm 2010 jeep wrangler
It still works on the 2012's but they took it out of the manual

Quote:
Originally Posted by CA3 View Post
Insert key into ignition, buckle seatbelt and turn key to on but do not start engine. Within 60 seconds, Unbuckle and buckle seatbelt 3 times, cycling seatbelt indicater on and off. Red LED in lower right of guage cluster will flash three times to indicate reprogram.
This should work. While your at it there are some other things you could do like get all the doors to open on the first unlock on the key fob. -->http://www.wranglerforum.com/f33/man...le-155357.html
06-14-2012 05:22 PM
CA3 Insert key into ignition, buckle seatbelt and turn key to on but do not start engine. Within 60 seconds, Unbuckle and buckle seatbelt 3 times, cycling seatbelt indicater on and off. Red LED in lower right of guage cluster will flash three times to indicate reprogram.
06-14-2012 03:42 PM
Oglethorpe Pretty sure it is in the manual (at least it was for my 2011)...

But Google does the trick, too

How do you disable seat belt alarm 2010 jeep wrangler
06-14-2012 03:31 PM
Ran-Bo
Programming Seat Belt Alarm

Hey all...does anyone know how to program the 2010 Wrangler to eliminate the annoying seatbelt dinger. My wife's 2008 Liberty was easy, it referenced it right in the manual...can't find anything for the Wrangler.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:28 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC