|07-22-2008 05:13 PM|
|Jerry Bransford||Yes both a bellyup (which lifts the t-case up) and a suspension lift will require a slightly longer DS. I think I'd wait until it's all installed before measuring for the new CV DS.|
|07-22-2008 05:07 PM|
thank you jerry!
i have a belly up to put on and will be going to 4" suspension(2" right now with stock tc skid), will that change the length(i would only think it'd change the angle...)?
|07-22-2008 12:10 PM|
|Jerry Bransford||Yes that was measured correctly, go for it.|
|07-22-2008 12:57 AM|
|NalinMFG||(psst i was actually asking if i did mine correctly, not showing what to do) hopefully if someone replies ill order mine tomorrow|
|07-21-2008 11:10 PM|
i believe this is where i start at...
so 19 1/4" ? thats what im thinking if i measured correctly
|07-18-2008 04:33 PM|
|Jerry Bransford||You don't need adjustable length front control arms to get your SYE and CV driveshaft installed properly.|
|07-18-2008 02:59 PM|
|07-17-2008 10:23 PM|
You can get away with just upper adjustable length control arms which will give you the correct pinion angle while at the same time restoring much of the wheelbase shortened by the suspension lift... a good thing. Using adjustable length lower control arms to raise the pinion angle would further shorten the wheelbase already shortened by the suspension lift.... not a good thing.
Shocks-wise, RE Monotubes, OME, Skyjacker Hydros, or the Bilstein 5100 (the version specially valved for Wranglers) would all be good riding choices. The RE twin-tube, Rancho R5000, ProComp ES-3000, Skyjacker Nitro would be commonly available choices that most would consider as way too stiff for a Wrangler.
|07-17-2008 08:18 PM|
|07-17-2008 06:42 PM|
RE's kits are pretty much identical to any of the others, I'd buy one from them as readily as the other companies I mentioned... they're all fine quality.
Length-wise for the CV driveshaft, it depends on your suspension lift height. I waited until I got my lift installed then measured for the length. RE may be able to tell you what length CV driveshaft you need based on your suspension lift height, I know Tom Wood can ship you the right length driveshaft after he talks with you and learns how your Jeep is set up.
The most accurate way to know of course is to measure for the CV driveshaft once the SYE kit has been installed. Use example '2' as per below for how to measure once the SYE kit has been installed.
(illustration courtesy of Tom Wood's website at http://www.4xshaft.com/index.html)
|07-17-2008 05:45 PM|
|AzTJ||Check out 4x4groupbuy.com - they have a number of RE kits available that include an SYE and Driveshaft. I bought my kit through them and love it.|
|07-17-2008 04:19 PM|
alright im fairly new to this whole jeep thing and i understand that if i do not get a SYE and CV driveshaft i will have to lower my transfer case which will reduce ground clearance and seams fairly ironic since i want more ground clearance in the first place.
Anyway, i checked out tom woods and a couple other sites you listed but i still found a SYE and a CV driveshaft for about $400 from RE, and i would prefer to have all my parts coming from the same source. Im not sure if the RE stuff sucks or what but i think it would be better to go with them since iam buying my lift kit from them also....another thing i dont understand is what the inches are for and mean when buying a driveshaft..? You can see all the driveshafts RE offers here... http://www.rubiconexpress.com/Produc...=05BDD66854068 but i dont know which one is right for me. The SYE which iam looking at buying is here .. http://www.rubiconexpress.com/Produc...=05BDD66854068 and they recommend the CV driveshaft (RE1898) but doesnt say anything about length or what not....just need some guidance so i dont screw this up...thanks!
|07-17-2008 02:44 PM|
Pretty much any SYE from sources like Tom Wood's Custom Driveshafts, JB Conversions, Advance Adapters, etc. would be fine. Tom has a complete kit for a pretty good price that would be hard to beat.
I would avoid JB Conversions "super short" SYE which while it sounds good, that kit eliminates the speedometer gear which then makes it impossible to recalibrate your speedometer without an expensive external electronic speedometer calibrator. Besides, a super-short SYE kit is not needed for any but the tallest of suspension lift heights.
|07-17-2008 02:35 PM|
slip yoke eliminator and CV driveshaft
Im buying a 3.5" standard lift kit from RE, and was wondering where and/or what kind of slip yoke eliminator and CV driveshaft i should get for my 98 4cyl. tj. I decided on RE because i can easily upgrade to a 4"+ superflex system if i want to down the road. Any help would be appreciated. THANKS