Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Will Rod bearings do the trick?

Join Wrangler Forum Today


Thread: Will Rod bearings do the trick? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-19-2012 08:43 AM
crallscars
Pull the pan and see whats wrong.

Sometime back with about 80,000 miles, I heard what I thought was a rod knock after I lost oil pressure. Long story made short, the oil pressure turned out to be an intermittent oil pressure sensor, and the knock was the AC compressor clutch, but better to be safe than sorry when you see no oil pressure on the highway.

I pulled the pan and plasti-gauged the rods and mains. My crank looked good with no signs of wear, the rod bearings were showing signs of wear, and the mains were within tolerance and looked like new. I replaced the oil pump and rod bearing only. When you change your rod bearings, plasti gauge a new bearing and check your clearance, there are 0.001 over sized rod bearings available which will bring a worn crank back to tolerance.

I now have 230,000 miles on the Jeep and have a solid 35 psi at idle after a long drive on hot day in Florida.
06-18-2012 09:39 PM
div4gold If you don't have the time to take it down then just drive it and if it starts getting worse look for some alternative transportation until you can fix it right. Good luck.
06-18-2012 08:02 PM
Atthehop I would pull the engine and tear it down on an engine stand. Much easier than jumping up and down.
06-18-2012 08:01 PM
amedley thanks Div4gold...i understand replacing the mains and cam bearings..i was just wanting to put a band aid on the main problem right now..i also thought it could be a wrist pin.

i dont have another means of transportation right now..was looking for the quick fix
06-18-2012 07:30 PM
div4gold You can't get the piston and rods out the bottom. You could replace the rod bearings but I wouldn't do that without replacing the main bearings and cam bearings. I don't know the exact symptoms but it could also be a wrist pin making the noise. You are going to have to take the head off to get the pistons out. You more than likely won't be able to see any wear. You will have to plastigauge the bearings or mike them.
06-18-2012 07:08 PM
amedley Ok Exhaust pipes are a problem to get off...ugh
06-18-2012 01:35 PM
amedley
Will Rod bearings do the trick?

hello Jeepers,

I have a 2000 jeep wrangler sahara..4.0 liter
I am getting a knock in the engine.. was wondering if it could be piston slap due to a worn rod bearing. it seems to be coming from one of the back pistons. it has lost oil preassure but no smoke..makes me think bearing and not rings

I plan to pull the oil pan in a few moments to see if i can find the one with the wear.

i also plan to do a total rebuild but the timming sucks..as the jeep is my only means of transportation right now..i want a quick fix just to get me by til i can do the complete rebuild

questions i have:
will i be able to visually see the wear..or do i need to use a feeler gauge?
is it possible to remove a piston and rod from the bottom of engine with crank still in? i didnt want to remove the head at this point.

thanks for your input
Adam

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:12 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC