Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > bent my tailshaft

Join Wrangler Forum Today


Thread: bent my tailshaft Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-25-2008 02:46 PM
schlik
Quote:
Originally Posted by Jerry Bransford View Post
Do you have a suspension lift installed? If so, and if it's tall enough and you're still using the OE driveshaft, that is often the reason for a bent t-case output shaft. The too-short-for-the-lift-height driveshaft nearly pulls off the splined output shaft when the suspension is fully flexed but it doesn't pull off all the way, cocks slightly, then jams and bends the output shaft as the suspension tries to push the driveshaft back down onto the t-case output shaft.

So if you do have a suspension lift and it's tall enough, it'd be a good idea to install a SYE kit and longer CV driveshaft to prevent this from happening again.
yeah I have a RE 3.5 in standard. That makes sense. I've been high-centered on the skidplate a few times, so i would like to get rid of the t-case drop. Besides this will probably happen to me again if I just repair the bent one. It will be better in the long run I think.
07-25-2008 11:54 AM
Jerry Bransford Do you have a suspension lift installed? If so, and if it's tall enough and you're still using the OE driveshaft, that is often the reason for a bent t-case output shaft. The too-short-for-the-lift-height driveshaft nearly pulls off the splined output shaft when the suspension is fully flexed but it doesn't pull off all the way, cocks slightly, then jams and bends the output shaft as the suspension tries to push the driveshaft back down onto the t-case output shaft.

So if you do have a suspension lift and it's tall enough, it'd be a good idea to install a SYE kit and longer CV driveshaft to prevent this from happening again.
07-25-2008 11:42 AM
MOz Why not just replace the broken component?

An SYE and custom shaft are a nice to have (if you really need them). Question here is, did you need it before you toasted the last one? If it was OK before, why spend all the extra cash?
07-25-2008 01:54 AM
schlik
bent my tailshaft

OK so I took my jeep wheeling this weekend and while paying a little less attention than I should, my front tires dropped into a ditch. it wasn't wide but was quite deep. I threw it in reverse to get out and thought nothing of. While headed home I noticed major vibes. They start around 20mph and get worse from there. My mechanic looked at it and used the alignment rack to show me just how much it moves (alot). My question is will installing a full spline replacement SYE cure the problem? (I mean I might as well, right?) Also do I have to get the adjustable control arms right away, or can I put them in and correct the pinion angle a week or so later?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:56 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC