|07-01-2012 10:02 AM|
I decided to have the air line follow the diff vent tube and to stay away from the exhaust
Wiring everything up right now, going super smooth. Anyone notice the master 40A fuse is very close to the pump instead of the battery (the way it should be). Did anyone relocate theirs so it's closer to the battery?
|06-27-2012 06:29 AM|
Is this similar to yours?
|06-27-2012 12:57 AM|
You did exactly what I did to install the compressor. I ran my line down the top driver's side control arm if I remember correctly so it would flex at the two joint and nowhere else. So far so good as I have not had a problem at all and yes use lots of zip ties just in case. I can fill all four 31" tires from 14 psi up to 35 psi in right under 10 minutes. Not super fast, but helps when driving a long way.
When doing elephant hill in Moab there is over an hour of driving just to get to the trail head. It was nice to air up after that trail.
|06-27-2012 12:41 AM|
Give the same advice as I got from ARB tech support (which is top notch. You talk to a live person from the minute they answer till your done; which only takes 5 minutes as they know their stuff and do whatever it takes) zip tie the shit outta it. If it comes near something tie it to it (if it 's not a moving part)
But looks good!
|06-26-2012 10:43 PM|
I liked doclouie's setup so I tried it out, it allowed excellent space for being able to work on everything
In case anyone in the future is curious, here is how I mocked everything up
First I placed the compressor on the ABS tray with solenoids and pressure switch installed and marked where the base laid with a marker. I then removed the ABS tray and marked it all up again. It turns out the location I chose just happened to line up with an existing hole and a welded on nut (probably for ABS?). I drilled out the nut and cleaned it up as seen below
I then lined up the rest and drilled two 1/4" holes
I then tried mounting the tray with the pump and base plate installed but there was no way to make it fit without pulling other stuff. I installed the ABS tray alone and then installed the pump. It was extra work and took a little more time but I was able to do it alone
I'm very happy with this location, I even installed the solenoids after the pump and had no issues.
I had no issues routing my rear air line, anyone care to comment on this setup for the front?
I ran it up the front near the radiator with the diff vent tube. I'm kind of curious how this would play out at full stuff, I don't feel like pulling my coils to find out.. It seems like the frame might start coming down on the air line
|06-26-2012 07:38 PM|
Mine is mounted to the front bumper - I'll have to move it if I ever get a winch.
Had a cover made up for it - keeps the crap off out on the trail - ARB also reccomend keeping it out of direct sunlight.
|06-26-2012 04:47 PM|
|MikalCarbine||I don't have cruise control so I have plenty of room, I do have my master cylinder (5 speed) but it's no big deal. I'm just curious of other peoples configurations|
|06-26-2012 03:44 PM|
You can move your cruise control.. Mine was moved when I did the fender/vent mod. Not that hard to just move it up higher on the inner fender to get the room down there.
In the install write up link I posted the guy talks about how he moved his.
|06-26-2012 03:26 PM|
|06-26-2012 03:24 PM|
|06-26-2012 02:54 PM|
|erickpl||Poison Spyder DeFenders?|
|06-26-2012 02:05 PM|
It's.not any fun but you can get it on the tray
I put the little manifold block up high so it would be easy to get to, and wouldn't have to be digging around to put the air hose on to fill the tires.
this is the vent I have. Being able to remove this made a huge difference.
|06-26-2012 01:30 PM|
I don't have inner fenders or that tray anymore. So we put it on a custom bracket welded to the frame. On my jeep, this location sits up high enough and hasn't caused any problems after river crossings.
If I had the ABS tray, that seems like the ideal location.
|06-26-2012 01:12 PM|
|doclouie||Attachment 135626I do have cruise and you cannot do that, but that is exactly how I got mine in. I removed the cruise control. It would be easy enough to get to if needed.|
|06-26-2012 12:38 PM|
|cashcow1608||When I mounted mine I was able to pull the tray out. mount the compressor, then put the tray back in with the compressor mounted to it. I dont think you can do this if you have cruise control though.|
|06-26-2012 12:27 PM|
|XMRacer||I'll post pics in a little bit..|
|06-26-2012 07:47 AM|
|MikalCarbine||Any pictures you guys? Did you take into account servicing the pump and parts on the trail without having to remove it? I could make the pump "fit" in 100 different configurations but I think allowing it to be serviceable is a wise attribute in the install|
|06-26-2012 01:39 AM|
I too have this compressor and got it on the ABS/ Spare battery tray. I don't think I would have gotten it mounted if I didn't have vents plates in back of the fenders that I could take out.
I followed another members very good install write up here
If you decide to relocate yours I'll give you all the help I can as it was a serious PITA but worth the hassle.
|06-26-2012 12:11 AM|
|doclouie||That is the exact pump I have and yes I put it on the ABS plate. Not the easiest spot to work on, but it works. It will help if you do not have cruise control.|
|06-25-2012 10:30 PM|
ARB CKMA12 Mounting Locations
The ABS tray seems like the obvious spot. Anyone have pictures with this specific pump? After a couple configurations I came up with this.
It allows the solenoids and pressure switch to be worked on or replaced without removing the pump although it'd be a huge pain. The air filter is kind of cornered and probably won't receive the freshest airflow but I don't think that will make a huge difference
Any other setups?