|07-02-2012 10:24 PM|
Will do. I'm definitely tackling mine next week.
It's frustrating, yet funny; I contacted BesTop about a solution & all they could do is recommend a body shop. I think not.
|07-02-2012 10:20 PM|
|johnpmcelroy||Permatex Black Silicone Adhesive Sealant. I've also made the decision as to the tightness. Right now I go only Finger tight and I carefully watch as the covers start to press against the Jeep Seals when tightening the screws. I've also been making washers from Plastic containers and Plastic container Lids such as Folgers Coffee. And put alittle grease on everything. Keep us updated on this issue. This really makes me wonder, everyone has got to have this problem. I would not want to see what the price is for those 2 covers. I would imagine at least $300. You never did say how bad yours was cracked.|
|07-02-2012 08:10 PM|
Thanks for the input John! I'll be tackling the same thing on mine next week
Which sealant did you use?
|07-02-2012 12:27 PM|
|johnpmcelroy||I took my 2 tops off to determine the max rotations it was and both were approx. 18 turns. And made a note of it with a Sharpee Pen on the covers. I got some Tool Box Shadow Foam and made washers. Now the turns are approx. 10 rotations when tight. Eventually the foam will get compact. But at least I know I have the problem and how to fix it. Also I cleaned the area on top where the small cracks are and applied some Black Adhesive Sealant.I hope thats the end of it.|
|07-02-2012 11:06 AM|
|johnpmcelroy||I'm gonna remove the two tops and determine how many screw turns it takes before the screw hits the plastic from the inside. This will determine how many turns you can go when you put the tops back on your jeep. I'm pretty sure this is what is happening. I will most likely be making some thick washers so this does not happen anymore.|
|07-02-2012 09:07 AM|
|johnpmcelroy||Anyone try to figure out why it crack where it does. Is it from the Screw going up to far and hitting the plastic|
|07-02-2012 05:42 AM|
I just noticed the crack myself. Plastic is hard to repair permanently. I'm thinking, Clean the crack area real good. Find some thin 1/8" Plexiglass, and make plexiglass patch. Probably 1" to 1-1/2". Question is what to use to glue it. Either Epoxy or an adhesive they make for plastic.
I did some plastic molding repair for Large Truck interior molding, using plexiglass and epoxy, and was surprised it worked.
|06-19-2012 03:08 AM|
Thanks to both of you for your input
|06-15-2012 11:06 AM|
|RioWrangler||Couldn't you repair it the same as a fiberglass boat? I think they sell kits that include a gel coat.|
|06-13-2012 10:24 AM|
I actually had a pretty big crack that shattered my window on the back passanger side of my hard top (damn tree....). I did pretty much what you said, I put on some epoxy (inside and outside) and then a nice black waterproof coating on the outside (can't remember what it was called...).
It looks pretty good, the only problem is the epoxy does stick out and it is pretty clear that it was repaired (adds character if you ask me). I may sand it down a little bit eventually, so have it blend in a little better, but at the same time I do like the rugged look.
|06-13-2012 05:58 AM|
Bestop Hard Top Crack Repair
Has anyone had to fix small cracks the spur from the bolts/bolt holes in the top of their hardtop? I'm sure a lot of you have.
I am not a body man, I usually stick to mechanical, pneumatic, hydraulic, & electrical.
I was thinking about getting a good epoxy from the auto parts store & working it into the cracks to keep them from spreading & getting bigger.
Does anyone have any better suggestions?