Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Spare tire won't fit after rear bumper install

Join Wrangler Forum Today


Thread: Spare tire won't fit after rear bumper install Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-05-2012 11:41 AM
TnDz TJ
Quote:
Originally Posted by Neil F.

If you do the above, or whatever you do it is VERY important that you keep the rubber bumpers on the tailgate and tub tight against the tire. It the bouncing and twisting of the spare that will wear on the tailgate hinges and carrier causing problems. Space the bumpers out as required to keep contact with the tire.
Lol. I kinda left that out thinking that was a no-brainer that needed to be done.
07-05-2012 11:41 AM
roastemover Thanks for all the input, I will look at all those options. This is exactly why the forum is a great tool for newbs.
07-05-2012 11:29 AM
TJspeed
Quote:
Originally Posted by AFGUY1980
Stay away from body lifts. They are bad news and they look nasty. Good luck
You should read up a bit more. A small body lift does some good. A 1.25" body lift is perfect added with a 1" motor lift. Fixes drive line, allows a tummy tuck easier, allows an aftermarket gas skid to install easier, allows just that extra bit of clearance for tires. But 2" and more are just dumb and look bad and cause issues. Those are a bad idea. But a 1.25" and less is perfect.
07-05-2012 10:05 AM
TJDave
Quote:
Originally Posted by AFGUY1980 View Post
You don't need a body lift and it is fine to run a 33 inch tire on the stock mount. I have been doing it for years on several different jeep tj's.
I am curious how you gained the clearance without a small body lift and the stock carrier. Mine would not fit with the stock bumper, or my aftermarket bumper.
With clearance, and properly supported, running on a stock carrier will work just fine. If the Jeep sees mostly pavement, it would probably last a lifetime.

Quote:
Originally Posted by AFGUY1980 View Post
Stay away from body lifts. They are bad news and they look nasty.
I am also curious of the "bad news" that will happen with just a 1.25" body lift. It's pretty much a requirement if you want to do a tummy tuck. I am surprised that Rokman, Savvy, or UCF does not include this warning when they sell their high clearance transfer case skids. Savvy even includes a 1.25" body lift with their Under Armor system.

To each their own I guess. My 1.25" body lift is barely noticeable. Less noticeable than the ridiculous looking stock dirt brake/TC skid that used to hang down underneath my Jeep. No bad news with my BL after 4 years.
07-05-2012 06:49 AM
Neil F.
Quote:
Originally Posted by TnDz TJ View Post
Just grab some 1.25" square stock and space the carrier off the gate for clearance....
If you do the above, or whatever you do it is VERY important that you keep the rubber bumpers on the tailgate and tub tight against the tire. It the bouncing and twisting of the spare that will wear on the tailgate hinges and carrier causing problems. Space the bumpers out as required to keep contact with the tire.
07-05-2012 06:30 AM
TnDz TJ Just grab some 1.25" square stock and space the carrier off the gate for clearance....
07-05-2012 02:55 AM
AFGUY1980 You don't need a body lift and it is fine to run a 33 inch tire on the stock mount. I have been doing it for years on several different jeep tj's. There are a few company's who make brackets that will extend the tire out off the gate an inch or so. I have even seen a bracket that lifts the tire up vertically off of your bumper. Stay away from body lifts. They are bad news and they look nasty. Good luck
07-05-2012 02:32 AM
TJDave 1.25" Body lift.

Tub mounted spare tire carrier...Or Fab, or Bestop.

I think Warrior products makes a different stock type tire carrier for oversize tires. But, you would be adding more leverage on the tailgate. The stock tailgate really can't handle a tire larger than 31" for very long unless you make sure that the rubber snubbers are extended out to the tire. That will keep the tire from bouncing around and help prolong the life of your tailgate. But even doing that, some people still have had problems. I was lucky and ran a 33" tire on my stock carrier for a couple years with no issues before I bought a Bestop tire carrier. But without my 1.25" body lift, it would not have fit.
07-05-2012 02:22 AM
roastemover
Spare tire won't fit after rear bumper install

I'm a newb Jeep owner and just installed a Smittybuilt rock crawler rear bumper on my 06 TJ. After the install the spare tire (32') will not fit, sits on the bumper and needs about 1.5 to 2 inches more space. Does anyone know of an adapter or have any ideas? I know this has to be somewhat common???

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:26 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC