Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > WF Local > WF Local Forums for Your Region and State > Iowa Jeep Forum > Anyone Gotten Nutty in Iowa?

Join Wrangler Forum Today

Thread: Anyone Gotten Nutty in Iowa? Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-08-2012 01:21 PM
Keymo Alrighty. Never mind y'all. Got it figured out.

Mods can close this tread.
06-24-2012 09:43 AM
Anyone Gotten Nutty in Iowa?

Hello fellow Iowans!

So basically I'm wondering if anyone in Iowa has done the "John Nutter Bypass" to their YJ? And if so, are you willing to give advice/help out when I do it? I have a 1989 YJ, 4.2L 6Cyl. Engine. I believe everything about my engine is stock (nothing has changed engine-wise since I bought it at least) including the carb..

First, the setting of the stepper motor and re-wiring. I feel like I've got this step down. Both the setting of the stepper motor and wiring seem pretty straight-forward. The only thing I'm worried about is getting the wires confused since my Jeep's wiring harness COULD have different colored wires than the ones in the tutorials I've read - though I can easily just follow the wires and figure it out. (I know I at least have purple and orange at the distributor, I'm more worried about the ones at the ignition switch...) I've already bought the 16 gauge wire, wire cutter/strippers, connections (male and female) and electrical tape.

Next, vacuum lines. This is where I get a little hazy on which lines I'm supposed to have all connected to the "T" connection and how exactly the "T" hooks up to my carb... (Oh, and what's the PORTED vacuum? Is this just a term for altering the lines or is there two vacuums in the engine compartment? I didn't see one other than the one under the coolant over-flow res....) Otherwise I could use some advice on vacuum line removal, though it's not completely necessary - I can look up the diagrams and figure them out myself if I need to... I still need to get a hold of the "T" connection - the guy at NAPA wasn't much help in general, so I just said screw it on the connection for the time being..

Finally, the timing of the engine. I've NEVER done this before, nor do I really know how to do it other than what I've read online. It seems easy enough, though you're supposed to set it quickly due to the engine running like crap after you re-wire and move the vacuum lines... I'd really like to NOT damage my engine... I figure having two people around would be best for this step anyway; not to mention if that someone knows what to do and can tell me when and how far to adjust the distributor as quickly as possible.. I don't have a timing light right now but I do know someone that has one. I'm also thinking about just buying a cheap one for this project and so I can have it for future tune-ups...

I probably wont be doing the Nutter Bypass anytime soon - I'm currently waiting to even start my Jeep again until I get the Cylinder Head Gasket replaced. My stealer cork one started leaking a little bit, so I decided to park it rather than risk any potential damage to my engine. I've ordered it, so now it's just the waiting game until it gets here... Once I have that seal replaced, and maybe replacing the bearings on my rear drive shaft, I'll be ready to go with the bypass.

I'm not looking for any hand-outs, nor am I asking anyone to do it for me. I would just like to have someone who actually knows what they are doing around to make sure I'm not screwing stuff up (and for MAJOR help on the timing adjustment...).

I live in Ames, so I'm pretty much in the center of the map. I'm not all about driving my Jeep long distances (mainly just to keep the miles off my engine), but I'd totally be willing to drive if I had to if it meant I'd be able to meet up with someone knowledgeable on this mod. The increased performance, better idling and potential improved gas mileage would be totally worth it! Plus, I like things mechanical so any removing of computers in general, I'm totally in support of.

ANY help would be greatly appreciated!
Thanks in advance!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 09:30 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC