Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Communications and Electronics > How to radio reset?

Join Wrangler Forum Today


Thread: How to radio reset? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-10-2012 05:35 PM
eboven Glad you got it working again... usually the reset needs AT LEAST 5 minutes to actually work, capacitors in the radio and other modules store voltage, so they need time to drain completely for the full reset. You can speed this up by shorting the device's positive and negative leads together, only after you have disconnected the device from power This is why you will sometimes see both battery cables disconnected from the battery, then held together for 30 seconds. The direct short will almost instantly drain any residual current left in the circuit. Just make sure that you don't have any external power going to the unit still, or you will let all the smoke out... you can't put it back in either!
07-10-2012 11:47 AM
ajkman Today I re-installed the radio and reconnected the battery after letting it sit overnight on a gut feeling that maybe it would work (even though I had tried this previously). Scha-zam - the darn thing started working again. It's a mystery that I can't explain, but it works now.

An easy way to see if your factory radio (09 Wrangler) powers up (assuming fuses are good) is to remove the dash as depicted in the video below. After this, pull the plugs from the back and remove radio. There are two bigger sections in the rear of the radio for plugs. They are separated by a smaller plug in the center. Looking at the back of the radio, you will be focusing on the big plug in on the right side.

Inside this are two larger flat pieces. You will need to connect a 12V battery to these pieces. Connect a negative (black cable) to the flat piece on the left, and a positive (red cable) to the piece on the right. To check if power is running through the radio, hit the eject button for a CD. The radio should do something as this point. All the supplies to do this can be picked up at Radio Shack. Cables with clamps at the end are helpful.

MYGIG LOCKPICK JK WRANGLER RUBICON - YouTube
07-09-2012 08:39 PM
ajkman Thank eboven for the reply! I drew some inspiration from the video below and visited my local Radio Shack for some equipment. The guys there let me play around with some stuff in the back. I was able to conduct a successful test of the radio with some extra wires, speakers and a couple of 12V batteries. The "bench test" revealed the radio to be in good working order. I will look at the wiring (maybe a bad relay?) next to see if this is where the problem lies.

http://www.youtube.com/watch?v=IB5wsicoAXM
07-09-2012 08:00 PM
eboven If it's the original Jeep radio, the only way to reset is to disconnect from power for 5+ minutes, then hook it back up. You can emulate this by disconnecting the battery for the same amount of time, then reconnecting it. Sounds like you did that already with no luck. There will not be a reset button unless it is an aftermarket stereo. Also, if it is an aftermarket radio, they usually have their own dedicated fuse on the radio chassis; unplug the wiring harness to access it. These are usually what blows when the vehicle is jumped and too much current is seen.
07-09-2012 06:30 PM
ajkman
How to radio reset?

I have a 2009 Wrangler X that wasn't started for a few weeks. I ended up jumping it with another vehicle and the lights and windshield wipers wouldn't stop working. I ended up shutting down the vehicle, and disconnecting the battery to reset these items (which are now working). This is when I noticed the radio was not working. I replaced the fuse (M10) and did the battery disconnect reset thing, but I still don't have a functioning radio. All other fuses appear in good order. I understand that during the jump the radio may have received too much electricity, and therefore, may have been shorted out. I have removed the radio and am looking for a reset button (or perhaps a method to reset). Is anyone aware of a fix for this issue (before I purchase a new radio)?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:02 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC