Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > U-joint problem on the Front Driveshaft Pinion side

Join Wrangler Forum Today


Thread: U-joint problem on the Front Driveshaft Pinion side Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-21-2008 09:42 AM
Beowulf So far there have been no vibrations indicating an out of balance shaft. To test I have run some smooth dirt roads in 4hi to see if that would induce an vibration.
08-21-2008 12:13 AM
rrich A little tip for others before they bend theirs:

Use a propane torch to heat the OEM injected plastic - it melts easy and shoots out, letting you push the cap out with very little force.

Now you may still have a problem - when you opened up the ears did they both bend out equally? If not, the shaft is no longer centered, giving a nice vibration.

Next time you run into something like that - check the book or ask here - or somewhere before damaging things.
08-20-2008 10:57 PM
Beowulf We measured my ears compared to my brother's which we had not tore apart yet. Indeed my ears were bent. We used a large bolt and nut placed between both ears and unscrewed the bolt. This did the trick and spread the ears to the appropriate distance that matched his drive shaft.
08-20-2008 10:05 PM
4Jeepn I would get a dana joint, I think its a 1310. Should not be a major issue to replace, some force of course but not like you said.
08-20-2008 08:33 PM
slf41002 I am not sure if the ears are bent or not but i think that is the wrong joint.I looked it up also and came up with a 369 or 280 so I would go back to the parts place and have them double check the joint and see if they don't come up with a 369,280 or one of the two you found.I would not force that one in before checking first.If that is one of the several correct joints that will or is supposed to work you can use a port-a par to spread the ears back out but I would check first.
08-20-2008 02:51 PM
yjwrangler you know what, i dont' know how to help you.. go to the parts store tell'em what you got and then go from there. you need a vice and a set of calipers to do the job, or hell a rock and a bfh (big f&#%n hammer) will do fine also. and you know 2 years ago in my senior year of high school i had a literature teacher who was obsessed with beowulf, now i liked the story enough, but i lost interest because of her...but thanks for taking me back there anyways..good luck
08-20-2008 02:21 PM
Beowulf
U-joint problem on the Front Driveshaft Pinion side

U-joint problem on the Front Driveshaft Pinion side

This is on a 2006 Unlimited Rubicon.

After having angry sparrows we tore apart my front drive shaft and greased everything heavily. Since the shaft was off we figured we would replace the pinion end joint. Of course these are the ones with the plastic clips. Using the Harbor Freight U-Joint tool we were able to push it out. With a huge amount of force and a loud snap the caps let go and pushed out. (I had no idea that they poured liquid plastic in the holes that filled groves in the ears and the caps. I thought they were just plastic pins)

When we went to put in the new u-joint the caps would not push in far enough for us to use the inner clips on both caps. It will completely bind before I can get the second cap in fair enough to insert the clip. The joint we are trying to use is a Precision 355. Oddly enough on the body of the ujoint it says 352.

From my research on the web we should be able to use one of the following joints:

Precision 355 or 290
Spicer 5-212x

Are these not the correct u-joints or did my ears somehow get squeezed together from the gargantuan force used to push the caps out? From measurements with calipers the joint is .03 too wide (or the ears are .03 too close).

Has anyone else ran into this problem?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:57 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC