Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Communications and Electronics > 2 ohm sub with 4 ohm speakers?

Join Wrangler Forum Today


Thread: 2 ohm sub with 4 ohm speakers? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-15-2012 07:57 PM
eboven To the OP: The speaker you wire into the amp dictates what ohm level you will be running. You cannot simply select 2 or 4 ohms, the sub is either-or. What sub are you planning on hooking up to the amp? Subs will have a "nominal impedance" rating; some are single voice coil, some are dual. Each voice coil will have it's own impedance, measured in ohms. If you have a single 4 ohm voice coil, you will run the amp at 4 ohms; there is no way to change that speaker to make the amp run 2 ohms. If your sub is a dual 4 ohm voice coil, than you can wire the two coils together in one of two ways. In a series configuration, your dual 4 ohm sub would be at a 8 ohm final load into the amp, while a parallel configuration would put your sub at a 2 ohm final load. Most car audio subs are a single 4 ohm speaker, but higher end subs will often be the dual 4 ohm speakers.

As someone else mentioned, your 5 channel amp will allow you to wire four 4-ohm speakers into the 4-channel part, and any sub configuration that does not measure below 2 ohms. You will get more power for the sub(s) at 2 ohms than at 4, but a 4 ohm sub will be slightly better sound quality; the lower the impedance, the lower the signal to noise ratio, meaning more distortion.
07-15-2012 01:38 PM
Jma20a do you plan on having a sub? of not that there is no need for a 5 channel amp.
07-13-2012 09:20 AM
Texas2070 Ya I'm gonna change amps. I'm gonna get an Alpine PDX-V9. It pushes out 100 RMS which is the same as the speakers max. Then turn down the gain a bit so there won't be any distortion. That will work right?
07-12-2012 12:42 PM
Jma20a If its a well built speaker or sub it can easily handle more than the rms level. I picked up a 15" death row from incrininator audio that is rated at 1500 and im pushing it on 1750.
07-12-2012 11:59 AM
Ibuildembig should be fine
07-12-2012 11:36 AM
Texas2070 One more question. Is it ok if the amp only pushes out 60 RMS and the speakers max is 100 RMS? Some people say that you should over power them by like 5-10 RMS. I wanna know if that will work well with my speakers.
07-12-2012 11:25 AM
Texas2070 Awesome cause the sub I was gonna get has a 300 RMS minimum and the Alpine amp only puts out 250 RMS at 4 ohm
07-12-2012 09:50 AM
Ibuildembig The amp you bought is made to do just that. The fact your other speakers are 4 ohm doesnt matter since channel 5 is made for a 2 ohm sub.
07-12-2012 09:39 AM
lee indy like anything you can blow it with enough power put to it. just dont get to nuts with the amplification. does that let you set your woofer separate from your speakers.
07-12-2012 09:37 AM
Texas2070
2 ohm sub with 4 ohm speakers?

I just bought an Alpine MRX-V70 amp and all my speakers are 4 ohm but I would really like to run a 2 ohm sub for more power. Is it alright to do this to the amp? Will it mess something up?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:29 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC