Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Electrical and Stall Problem - Please Help...

Join Wrangler Forum Today


Thread: Electrical and Stall Problem - Please Help... Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-27-2008 05:07 AM
jwh21236 Yay!!!!!! Thanks to everyone who helped me. The problem did infact end up being a defective battery bought from Wal-Mart. I returned it for another one, installed it, and the Jeep starts like a champ. Thanks again for everyone's help, it was very much appreciated.
08-26-2008 12:37 PM
rrich If there's a bad connection to the battery - either outside or inside the battery (thinking about it I suspect it's the negative side) - the alternator cannot charge it properly. It will try, the alternator voltage shoots up and goes out of sight - that's the 19 volts you see. It's trying as hard as it can.
But - the regulator tries to hold that voltage down, so interrmittently it drops the voltage back down again.

No matter how long you try to run it to charge it, with a bad connection it'll never take a charge.

The unstable lights etc - the voltage is bouncing up and down. But you only see close to the peak - as the gauge is dampened - it takes out the fluctuations. Use an undampened analog voltmeter on it - you'll see the radical voltage fluctuations.

It dies when you stop trying to rev it because the alternator voltage drops below about 10 volts, the ECM, the fuel injection, and the ignition shut down at about that voltage. Normally with a battery connected properly the battery supplies the need voltage at idle. Without that help ---.

Putting it in gear loads the engine down slower, the alternator itself cannot supply enough, it dies, same as the above reason.

Try swapping it out with a battery from another vehicle - or put the old one back in.

I have no idea why people resist such a simple thing. When I had my shops I made quite a bit of money on simple things like that - even after I told the customer how he could fix it himself. Go figure!

I suppose it's the "But I don't want it to be that!" syndrome.


My beliefs - diagnose FIRST before throwing expensive parts at it.
New does not always mean good.
And --- KISS!
08-26-2008 07:34 AM
jwh21236
Okay...but...

The problem was...I got it started by jumping it, then reved the engine continuously to between 1500 and 2000 rpms i guess for about 5 minutes. All of the lights in the vehicle were flickering as I was doing this and the electrical gauge read 19 instead of the usual 14. Then I went to move the vehicle, when I let off the gas, it dropped not only to idle, but it died in gear. That in essence is everything that happened. I had just bought a new battery and installed it so I though maybe it had something to do with that. Now I'm curious as to why it died in gear at all, because even after jumping it, I would think the battery has a little power to keep it idle at least for a few minutes, but it died as soon as I let off the accelerator, no idle whatsoever.
08-26-2008 06:04 AM
jdhallissey
Quote:
Originally Posted by jwh21236 View Post
If I did get the Jeep started, even by jumping it, wouldn't the alternator take over and keep everything stable electrically, including all lights, radio etc...? If it supposed to, would that mean to have the alternator checked?
Yes that is what is suppose to happen. If you jump it let it run for a few minutes drive it get it above 2 thousand rpm for ten minutes ie down the freeway. It should be fine but if not the first thing I would check is the alternator.
08-26-2008 06:01 AM
jwh21236
I just thought of something...

If I did get the Jeep started, even by jumping it, wouldn't the alternator take over and keep everything stable electrically, including all lights, radio etc...? If it supposed to, would that mean to have the alternator checked?
08-25-2008 01:12 PM
rrich That pretty much narrows it down. But first I'd have a close look at the terminal connection, just to rule that out for sure.

Wal-Mart batteries, the heavier duty ones, are made by Johnson Controls in Mexico. They are the ones that USED to make the Die Hard years ago (but no longer) - when the Die Hard was the best you could buy.

I don't think you can find better.

You may have a defective one.

The problem is it may test fine on their tester. If they tell you it's fine, YELL!
08-25-2008 11:00 AM
jwh21236
I'm sorry...

What I meant by new terminals was simply the terminals on the battery itself...I didn't change anything on the cable, only really cleaned the ends as best I could with a wire brush. They look completely clean, as in all shiny metal clean, both inside and out. I really don't think it's the connection of the cables to the battery terminals, but I am more and more becoming upset that I had to jump a new battery, who does that? I think I'll take it back and get a different one, and make sure that they test it before I leave. I still have the receipt and it was less than 30 days ago so I'm gonna take it back tomorrow. Is there a specific kind I should get? Or should I get my money back and just go somewhere else?

-Thanks
08-25-2008 08:55 AM
rrich New doesn't always mean good.
That goes for the battery and the terminals.

You had to jump start the new battery? Right from the start you knew it wasn't right - something wasn't.
Wal Mart batteries are supposed to be fully charged right at the beginning. If it wasn't, obviously something's wrong, you should have stopped there. The higher end of the Wally World batteries are made by John Controls, damn good batteries.

You said it has new terminals - you put on the new ends, not the entire cable? That in itself could be the problem. Those things give lots of trouble.

So there's another possibility - those replacement ends could be at fault. If you are using the side terminal connectors I'd really suspect those. Often they don't sit properly on the battery connection, the insulated lip holds it away.

Even the top terminal kind give trouble. Where the cable end connects to the clamp part - it only contacts part of the cable.

And then of course - the battery - inside where you can't see - the internal strapping sometimes is loose inside.
08-25-2008 05:20 AM
jwh21236
Okey...

I definately will re-clean the terminals, but I did use a very stiff wire brush to clean the leads. The battery terminals themselves should be fine since they are brand new right? Now I will admit that the battery did come from Wal-Mart, and maybe something is quite wrong with it because the Jeep wouldn't start and had to be jumped with the new battery??? A friend of mine said that's happen to him and it most likely had just lost charge from sitting on the shelf at Wal-Mart for so long. I will also check the sensor beneath the tray, although I hate having to pull that battery out again, for some reason it's a real pain in the ass.

I won't be able to do anything until Wednesday and I'll report back then, much thanks for the answers.
08-24-2008 12:29 PM
rrich He He - Knowing, wanting, or assuming it's making good contact isn't enough. The symptoms you describe - ACT like a bad connection. It's worth a try and costs nothing.
If that doesn't help, try another battery - no need to buy one, just use one from another vehicle or charge up the old one, the bad connection may be inside it - side terminals are famous for being bad.

Or you can first put in another alternator and ECM for a few hundred bucks, then try it. It's up to you.
08-24-2008 12:00 PM
Rawkon there is a temp/charging sensor for your battery under the battery tray. the main computer is your actual regulator.. id make sure the temp sensor thingy is plugged in and not messed up. then i would reset my computer your iac/tps wont effect the charge rate. also make sure your battery has a good charge on it. low electricity makes electronics do wierd things
08-24-2008 11:29 AM
jwh21236
Battery Terminals...

Thanks for replying so quick... When I installed the new battery, I thouroughly cleaned the leads off, so I know it's not that. Can the alternator actually cause a gauge to go higher though? That seems weird to me, that's why I'm wondering whether it is something else or not.
08-24-2008 09:00 AM
rrich Before panicking, clean the battery cables - it may be as simple as that. A bad connection can cause all kinds of goofy things to happen. It could even be inside the battery.

Sitting - could have critters eaten some of the wiring? Look close, they love insulation.

To help discourage rodents, put a few sheets of clothes dryer softener around. They hate the smell. They are good for a few months.
08-24-2008 04:42 AM
jwh21236
Electrical and Stall Problem - Please Help...

Hi all,

I recently put all new brakes on my 1999 Wrangler Sahara 4.0L and everything went fine with the install. The Jeep has been sitting for about 4 months though, maybe started 3-4 times, and when I went to start her up, she wouldn't start. I replaced the battery and was able to get it to start, but something isn't right electrically because all of the lights flicker like it's running purely off the battery and the electrical gauge reads 19, pretty much maxs out. It also stalls out when in gear from time to time. My question is...Is this most likely an alternator problem? Or does it have something to do with the IAC or TPS?

Thanks in advance for any help.

-Jay

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:36 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC